Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hi,
I run the radio test with our PCBA with SDK17.0.2, but when I want to send "start_tx_modulated_carrier 100", there's no callback response "<info> app: The modulated...
Hi.
I am looking to implement a nRF52840 chip in my 5v battery operated door lock.
Sorry if this is asked before or should be clear from documentation, but I am not...
Hi,
Do you have an example of how to implement a serial console with nrf connect 1.4.99-dev1 with nrf5340_REV1, I tried compiling usb_uart_bridge but got following error...
There are two central sd_* methods for writing to flash - write and erase. The problem is I need to know where I can put my data without trashing something else that is already...
I have two projects exhibiting the same problem.
I have custom board using the nRF52832 and another using the nRF52840. In both cases I am using nRF5 SDK latest version...
Hello,
I would like to have confirmation that the NRF52 will be compatible with my need.
The NRF52 must be able to be connected to a smartphone, while receiving advertising...
I have problems with my custom board.
I developed the firmware with the nrf52832-dk custom and there the firmware runs standalone (with RTT logs on and without) . but now...
I use a nRF52840 Dongle as the Sniffer HW. I use 2 other nRF52840 boards, one is a peripheral (NUS) and the other is a central/peripheral (NUS). The cen/per connects as a...
Hi I have a custom nRF52840 board, and I have a current BLE UART setup. I also want to communicate with a IMU module via serial connection. Can you point me in the direction...
hi,
ncs1.4.0\nrf\samples\bluetooth\peripheral_uart， The LBS service was added, but Advertising faile.
I don't know that I made a mistake in that step. It may be the address...
If I upload the pre-compiled asset_tracker file to the Thingy91, it works fine. If I compile it myself and try to upload it, nothing happens. It shows the write is successful...
I am trying to implement fstorage in my application using nRF52840, soft device 140, SDK for Mesh v4.0.0. and SDK 16.0.0 and Segger Studio.
Based on the fstorage example...
Hello,
I'm trying to develop a wearable stacking form-factor where number of boards can be assembled in a deck: MCU, sensors, actuators, power supplies, etc. Size of the...
Hi ,
I want to compile mesh examples .I tried it using segger ide Alternatively,I wish to compile it in cmake too. Can you please tell me the procedure to compile code using...
Hi,
I was able the configure the sample to connect to AWS but I cannot figure out where the cloud_send function is sending the data. Is there any documentation on where...
