Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hi,
How to implement two sets of SPI on the NCS v3.0.0 nRF54L15 P2 port? If it can be achieved, please provide the corresponding IO ports for these two sets of SPI.
Kind...
I have been forced to upgrade to the nRF54L15 from the nRF52840 DK. The example code in the SDK for the nRF52840 the 'ble-peripheral' had example code for 'ble_app_uart' which...
Hello Nordic,
I’m using ncs\v3.1.0\nrf\samples\peripheral\radio_test` to test the nRF54L15 with PHY set to `NRF_RADIO_MODE_BLE_LR125KBIT`. However, the RF spectrum measurement...
Hello,
I am developing a custom board based on the nRF54L15.
Every time I do RTT connection from the extension i have been asked to prompt the target device (nRF54L15M33...
i working bare-metal, using HW registers directly.... no zephyr, no SDC....
i'm able to successfully receive packets through the RADIO RX path, but now want to add a timeout...
Hi,
After installing nrf sdk v2.9.3 trying to build application under Windows fails with the following message:
Trying to run any command inside the NCS shell/terminal...
With nrfconnect SDK V3.3.0 seeing commissioning issues with light bulb sample with nrf52840dk and google home. The logs are given below. Please help with resolution
Thanks...
Hi,
We have an application where we have a working DFU over BLE with SDK 2.9.1 but once we have migrated to 3.2.4 it has stopped working. Something has obviously changed...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hi, I am working with the nRF54L15 on sdk-nrf 3.2.3 and I am experiencing an unexpected behaviour with the NFC T4T stack regarding WTX frame timing.
Here is the observed...
Hi Nordic team,
I’m working on an nRF5340 project using MCUboot with the secondary slot placed on external flash.
I found a strange issue related to pm_static.yml . My...
Hello Team,
I am trying to test a PDM microphone (MP34DT01‑M MEMS) on the nRF9151 DK using nRF Connect SDK .
So far:
I have successfully tested I2C and I2S DAC audio...
The drag and drop programming was working fine on previous boards.
We just purchased 10 boards thinking that they were the same, but the don't seem to work.
PCA10040 3...
We are developing the nRF5340 for the Thingy91X based on Connectivity Bridge (NCS 3.2.4). I want to output logs from SWD and view them with RTT Viewer, but even when I call...
Hello Nordic-Team,
I am using the SENSING mechanism on GPIOs to wake up a firmware from SYSTEM OFF. Two GPIOs are used for this and it is crucial for the firmware to detect...
