Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
The ble_advertising module supports the concept of advertising sets. Each set is connected to the soft device events by that compile time registration feature that routes...
Hi,
I try receiver test on the serialization application. The interface is UART.
The operation is the following.
1. Application board send ble_dtm_init command.
2...
Hi Nordic,
I am a 52840 user, focused on keyboard pcb. I designed several keyboards using GPIOTE, matrix scanning and other techniques provided by Nordic.
However, based...
Dear All,
I have added libraries of sensor BME680 to Segger Embedded Studio (IDE) successfully. But, I need help in displaying the sensor data on Serial Monitor (Using nRF52840...
Hello,
I am in the process of porting application code from the old nRF 15.x SDK to the new zephyr based ncs 1.5.0 SDK and would like to do all hardware configurations in...
Hi Nordic Team,
We've been long waiting for FEM support with multiprotocol and it seems like it is finally here with NRF NCS v1.5.0.
1- Can you please clarify, yes I can...
Hi
I tried to add the function of FEM to the Peripheral_hids_keyboard example according to the guidance of the link below. But it looks like it failed
https://developer...
hii this is rohit vekariya from bluesys lighting solution.
i am new in nordic can you provide example code for drive neopixel(ws2812) using nrf52832
thanks
I set up nrf52832 that it is proxy device, i create a loop that proxy device sent 20 message to app phone (Android) within 100ms. But my app (Android) receive only 1 message...
I'm designing the nRF52840 into a new product with BLE, LTE and GPS.
Could you please point me to a recommended matching network and antenna solution for the nRF52840? ...
I connected a button to LED on a breadboard, how can I write a debounce function to control a button. I checked app_button.c but it seems buttons they are using is button...
Hi, We have a custom design using an nRF9160.
We can connect and program the device using a jLink though the debug port.
How can we connect the LTE link monitor to the...
Hello everyone,
I get the following error whenever I try to build an application for the thingy91_nrf9160ns board:
The secure version works just fine.
For some...
Hi Team, I have design wireless node for biomedical application. I have used nRF51822 module in my PCB. I want to see the real-stream data from sensor (connected in input...
