Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hey all, I'm trying very hard to understand how UART over USB works by following through the USB CDC ACM example in SDK 17.0.2 on the nRF52840DK, but I'm still new to this...
Dear Nordic DevZone team,
I have spent some frustrating hours trying to find the difference between configuring my tiny application with nrf9160dk_nrf9160ns or my custom...
I revisited SES to see if I could understand it better:
File/Open nRF Connect SDK Project...
I Pick Hello World and my left side Project Explorer window shows the zephyr...
Hi.
I have Bluetooth and ANT+ LEV working simultaneous and they work perfectly. Now I need to send to a Garmin GPS display several custom data from my EBike motor that ANT...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi
Is it so that the only way to use Asset Tracker 2 is with this AWS? Not even with the nrf cloud?
I am following your instructions here
https://nordicsemiconductor...
Hi all,
I use nRF52832 with the UART peripheral example.
I use SDK V15.0.0 and Softdevice V 6.0.0, with IAR embedded workbench version 8.22.1
Messages output with NRF_LOG_INFO...
Hi,
I am using the nRF52840, which has 256KB of RAM, (i.e. loads and load of RAM.)
I would like to allocate a buffer of 45KB.
I have tried using malloc (from the stdlib...
hello nordic! I am using NRF52832 to verify certain characteristics of BLE. the question is:After the BLE terminal device is bound to the mobile phone( Most likely Android...
I found this in the schematic and I wanted to
Confirm this is correct pinout to communicate over serial
Know where to go in the firmware to get this information?
...
Hi everyone,
I am working on nrf52832 using sdk15.0.0 using ble_app_beacon
I getting 3mA current when falling edge detected, i want to set my device as low low power consume...
Hi, Dear Nordic & All:
I use usbd_msc example to generate .xls file, and write content in it, sometimes I write successfully, and can open it right on PC with WPS，
but...
In project ,i use a TWI transaction manager to control two sensor devices.So, each device requires a GPIO to detect input interrupts. I use a GPIOTE IN event and a GPIOTE...
What is the drawback of setting the TTL on mesh packet to a high number?
I am assuming that a node will not relay the same message twice? I.e. it sees a packet for the first...
