hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I'm just starting out with zephyr on a nrf52dk (nrf52832) and I'm in need of performing some math functions on the data output on a mpu6050.
The MPU6050 is spitting...
We are developing couple of products based on nordic 52810 and 52820. Mainly 52810 And we have received very good support from nordic team and very promp and pro-active support...
The documentation is unclear about QSPI handling:
If I issue a QSPI erase command then I receive confirmation that the erase command has been written to the external QSPI...
I'm using FDS module from nRF SDK 16.0.0.
Below I'll describe issue which I'm experiencing when trying to initialize FDS twice:
To be sure that my FDS filesystem will...
Was going through the process of updating the modem and application on my just purchased Thingy-91. Initially the programmer reported that the processor and two serial ports...
Hi,
I am getting this error with the new EVK 0.15.0 2020.42.
Any thoughts on what I need to do?
Thanks, David
%CESQ: 255,0,255,0
+CEREG: 2,"FFFE","FFFFFFFF"...
Where can I purchase the LTE RF fly-lead to connect Thingy91 to SMA?
I am right on the edge of LTE coverage here, and it would greatly assist testing to improve signal strength...
Hi Dev team,
I am working on a nrf9160DK and transmitting my sensor data to a MQTT Client. I tested this through an application : MQTT.fx (Using mqtt.eclipse.org as open...
To the kind attention of Nordic support team,
I ve been testing your sdk peripheral/usbd example in my S3 system and it is able to wake up the entire system when pushing...
Hallo,
Today I joined the seminar about "Using the nRF9160 as a Serial LTE Modem". It might be an interesting option for us to switch over to Nordic, we are currently using...
Hello,
I would like to synchronize 2 hardware PWMs between them (nrf52).
I mean with NRF_PWM0 and NRF_PWM1.
I tried to do this:
But it doesn't work, my 2...
I am using NRF52840 custom board and SEGGER RTT log for debugging.
I set the NRF_LOG_BACKEND_RTT_ENABLED 1 and NRF_LOG_ENABLED 1
The following is a screenshot of my...
Is there a way to trigger a work item on a nrfxlib socket event without a dedicated thread? Right now there is three polling mechanism in the SDK:
Zephyr k_poll(), which...
The Nordic 52810 that I'm using now for my development project has to do with the pairing of Android and iPhone. Android is available through Bond and Delete Bond in nRF Connect...
