Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
I was downloading a project to the flash memory using J-Link SDK and I am having this messsage:
JLink info: ------------ DLL: V6.80a, compiled May 29 2020 16:27...
Hi,
I tried connecting the thingy91 out of the box and it was working fine, sending data to nrfCloud.
Now I tried to build the asset tracker application on my own and...
Hi All,
I am facing the issue with sleep current in nrf51822. initially i checked the sleep current 11uA. but after one hour it is increasing to up to 390 uA gradually....
Hi All,
I am currently designing a BLE module using nRF52840 chip which works with battery.
In the nRF52840 DK, it uses a Power Switch Driver ( SC728CSTRT ) from Semtech...
I want to add a button function to the ble_app_uart.
I don't need to use the functions of the BLE Button Module.
It's enough to just change the value of the variable when...
Hello,
I'm trying to develop a small module based around the nrf52832 chip, and I am trying to replicate the reference design and layout as closely as possible. One problem...
Hello,
I am updating my application from older SDK 15.0 to use SDK 17.0.
NRFX_NFCT_ENABLED NRFX_CLOCK_ENABLED are used to enable the files nrfx_nfct.c, nrfx_clock.c respectively...
Hello DevZone,
I am developing a system that has a SoftDevice, UART bootloader, and application. The SoftDevice is S132 SoftDevice v6.1.1. The UART bootloader and application...
RTT seems to be mostly working using the viewer with the command:
JLinkRTTViewer -device nRF52840_xxAA
It seems I need to re-connect each time I start a debug from SES...
Hello Nordic
We are in the process of product development and at the moment we need a chip that transmits stereo audio to any BT headset. That it is possible to control...
I am using nRF52840 as a master to communicate with esp32. For esp32 i am using arduino ide and esp 32 slave library( available in library manager of arduino ide).
For nRF52840...
Hello,
I use nrf52832 with 65 kb RAM.
I can't understand why soft device takes about 30k RAM memory.
I see "reserved_ram" has 30k.
Can I change size for 20k for...
We're using the nRF52840 on a battery-powered device that requires very low power consumption, both in run mode and also in the Cortex-M4 sleep / deep sleep modes. We've recently...
Hi, I'm trying to enable the entropy driver so that sys_csrand_get() will stop returning "Entropy reseed error". Does anyone know why it's grayed out? I have tried enabling...
