Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
Recently I was able to get a single read and write SPI operation to work properly with a custom nRF52832 (BL652) with SPI connection to MCP2515 (CAN SPI) using the nrf_drv_spi...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I am attempting to import an existing IAR project to SES / GCC and am having some trouble. I recently joined the project team and we are making an effort to switch from...
Hello,
So I'm trying to modify the mqtt_simple sample program to connect to azure iot
I've modified the code in a few ways but when I went to run the program it gave me...
hello,
below is the error experienced.
nrfjprog --family NRF52 --eraseall ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists, run the...
Hello,
I'm using a nrf51422_xxac_s110, with the Keil uvision IDE. I recently upgraded my sdk from an older version, to 12.3 in order to use some components like FDS. Consequently...
Hi guys, I'm using a HFCLK TIMER to time ADC sample capturing via PPI. This eliminates CPU+BLE usage from affecting my time keeping. I assume that each ADC sample arrives...
Do you why I could not pass the "ble_stack_init()? I did download softdevice from 0x0000-0x26000 and Application from 0x2600
int main(void) { // Initialize. log_init();...
I can run some of the samples on my nrf9160 DK, however when it comes to this one I get a assertion error err==11 that I have not yet been able to solve.
ncs/zephyr/subsys...
Hi,
In my application I need accurate calendar capabilities such as alerts on every hour and alert on a specific hour every day. Is there any implementation of such a mode...
Hi,
Want to read data from HX711 adc amplifer with wheatstone bridge loadcells, but when i run the program, my output is <info> app: ADC measuremement -8388608 all the time...
I'm a little confused by the packet rate I'm getting on Gazell. Or rather I'm confused by the low number of 'timeouts' I'm seeing - I'd expect to see more, and would like...
Hi all,
in my custom board I'm using an NRF24L01+ as RF transceiver. The relevant part of schematic follow: (hi res => https://imgur.com/a/z4nQxXh )
The following...
The nRF905 chip can be setup to different payload length. 0-31 byte
Must RX and TX unit be setup to same payload length or can RX unit be setup to ex. 20 bytes and TX unit...
Hello.
There is a label on the back of the nRF9160DK.
I can find "HWID: FF:6A:B3:34:69:AC" on the label.
nRF connect can get the same string: " FF:6A:B3:34:69:AC " when...
