Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
We are using the secure BLE bootloader from the nrf52 SDK versio 15.2. We did put in our own key files, but other than that I think that I don't think we changed much in the...
Hi, I am a beginner with nRF52840. In the SDK under modules/nrfx/templates we find a file "nrfx_glue.h".
This file contains macros that should be implemented according to...
Platform：NRF51822, SDK12.1 S130
Phenomenon：By flipping the led light in the NRF_RADIO_CALLBACK_SIGNAL_TYPE_START event, it is known that the timeslot request is normal....
This maybe a stupid question but is there any reason to include support for older versions of the SDKs? I am using the pc-ble-driver approach and the example is full of if...
Is there any new information released about the GPS current consumption of nRF9160? I want to estimate the battery lifetime of a 1000mAh battery running the asset tracker...
Hi,
I am under long run test between coordinator and end device.
End device sends a message and goes into system off state until next event(door open) for minimal power...
Hi Everyone,
I am having problems writing to an array in NRF52832 without causing the program crashing at run time.
I declare the array to be 512 uint8_t long
then...
hi, I'm a fresher of this kind of development. My boss give me a board and let me run the Zephyr OS on it. But I am not sure whether I lack some things and how to assembly...
hello I am just needing some clarification on meshing. I am using the long range nfr52 chip. I have a transmitter with a tilt switch that connects to my receiver when connected...
Dear Support team,
could you please advice how can I change the endpoint where Thingy91 sends the measurement data stream from the sensors?
By the default it it is the...
HI, I'm Rafael Fajardo a student at Las Palmas de Gran Canaria University . I am using the nRF51 Dongle and following the Sniffer User Guide, but when I got to the final step...
Hello,
Zephyr has their own Bluetooth stack. Has anyone done an objective comparison of the Zephyr stack to the NRF52 soft device stack? I am very familiar with the soft...
Hi,
I'm currently making energy measurments with an nrf9160 DK. The software project is based on the udp_with_psm sample. I would like to run the test on different tx-power...
When debugging with Keil, the software may suddenly start from the beginning. The reset process may be running somewhere, but it cannot be detected. Is there information that...
