Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I'm upgrading a big project from SDK 6.0 to SDK 12.3, everything's going well, but I had to comment out a library because in SDK 6.0 the previous developer uses the input...
Hello there
I am trying to program the BL651 wich makes use of nRF52810 chip, however i haven't been able to program it.
The tool im using for the task is the J-Link...
from SDK 3.1 for thread and zigbee in simple coap server
after any time it go to disabled mode and no response
what means the flags? why is it disabled and do not...
Hi,
I want to create my own bootloader for the nrf52810. If i don't want to update my softdevice i just put my bootloader code just after my softdevice.
But it is not...
Hi everyone, I am wondering if there exist any list of Known Issues for SoftDevice S130 v2.0.1. I looked into the release notes published in PDF along with the hex files,...
Hi
I have a question about the new chip nRF52811, it supports AoA direction finding, but it doesn't support Bluetooth mesh?
There's no chip can support both AoA and mesh...
Hello,
I am using the nRF24L01 + circuit on a PCB made according to reference design.
Can I use a 0.5 or 0.6 mm thick PCB? Reference design is made on 1.6mm PCB thick.
I'd like to sniff the BT packets between a remote control and a bed (which is controlled through BT4.2), in order to control the bed through an android application.
Can...
I am using uart to transfer data in a while loop, and it works fine. Now I want CPU to go to sleep mode with sd_app_evt_wait(), and CPU to be waken up via Button then receive...
Hello
I'm working on Smart Remote custom board, which is based on nRF52832.
My Setup is running very well but only when RTT Viewer is connected.(and advertising led is...
I am using the TWI peripheral and want the clock frequency to be 400kHz.
In the data sheet it says for the register setting: 0x06680000 = 400kbps (actual rate 410.256 kps...
Hello All,
I am Facing issue in advertising custom board NRF52810.
I am trying to do the led blinking program on above board.
Using the SDK 15.3 with S112 . The hex...
In Nrf5 sdk V15 their is a micro
ticks = APP_TIMER_TICKS (MS);
My question is what is the maximum value of ms which can be used as input.
the same question goes to the...
Hi, I'm looking for information about duration of peak current on BLE and NFC mode on nRF52840.
Do someone have any answers ?
I saw that peak current on NFC is 80mA max...
Hi
I am using SDK12 with NRF51822,
So far I haven’t initialized the sys_evt_handler ( softdevice_sys_evt_handler_set(sys_evt_dispatch) ) And my program works fine, ...
