Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello!
I have 3 NRF52840 Preview DK's with Q1AAAA revision ICs. I have been putting those to good use, but I want to test some stuff with SPIM at 32Mhz, which I understand...
Hi,
I am using nRF9160DK, nrf v0.4.0, zephyr v1.14.99-ncs1
I have been trying to measure the boot time from when I press the reset to when it gets to the start of the...
Dear All,
I am trying to enable brown out detection to my NRF9160. From what I see in the data-sheet there is a register that you can set the brownout threshold, but there...
Hi,
looking at the ifx_optiga_custom_example in the nRF5_SDK_15.3.0, i see that for the Hashing calculation the oberon backend is used instead the optiga backend, Why? Is...
Hi,
I see your web: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer#infotabs
There are 4 hardware (DK x 3, Dongle x 1) we can choose to used...
Hi,
I am using nRF52832 with sdk15.3 SES
I need to use DFU.
Buttonless DFU
need to program the controller without the wire connection.
Can you explain how DFU works...
Recently, we are using Nordic resources and developing our own application. We have blue tooth integrated in app, also we have display and our own file system integrated on...
Hi,
I'm working with nRF52840 DK and I want it to advertise iBeacon packets.
I tried the beacon example on ble_peripherals from nRF5_SDK_15.3.0 SDK.
1) nRF connect and...
Hello,
My project is on nrf51822 in which I am using BLE and UART interfaces.
There is single UART available on nRF51822 and I am using it for communication with an...
Hi I am using the custom_ble_service example from https://github.com/bjornspockeli/custom_ble_service_example/blob/master/main.c . The example code will turn a custom characteristic...
HERE is the fix for this problem. It has been reported before (by others) with no reply. I hope that this fix or its equivalent will be incorporated into the next SDK release...
I want to interface a 16MB external flash (SPI) with nrf52832 on the development board.Suggest me how should I start with and if there is an example for external flash then...
Hi Great Support Team:
In the spec of 52832, the rx sensitivity is -96dBm @ 1Mbps.
I'd like to know if the sensitivity is the same (-96dbm) while we adopt ANT+ protocol...
I am using the nrf52840 with freertos and bluetooth (based on the HRM example). Application is designed to sleep for a set period of time before the RTC timer wakes the MCU...
