When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I collecting Heart Rate data using nRF52 and Max30102
I saw data in hyperterminal, it is normal and not show duplicated data,
but, I connected with my phone and nrf52...
Dear Nordic Developer Zone,
I have incorporated LESC in the following development environment. 【Development environment】 ・nRF51822 ・SDK12.3
The following function is executed...
Hi, all
I'd like to get the whole thread network topology (like nRF_TTM does) on raspberrypi, can this function be realized with wpantund or wpanctl?
Is "wpanctl mfg....
Hello,
I am attempting to integrate FOTA (HTTP Application Update) into a Thingy91 project on top of the LTE BLE Gateway example project.
I am on nRF Connect SDK v1.1...
Hi,
How many SPI slaves can I connect to nRF52832 as an SPI master?
I would like to know the maximum number of SPI slaves which can be connected to nRF52832 as an SPI...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hi,
I am using NRF52832 for development without bluetooth SDK, NFC and RTC.
I am using a development board with SPI and a slave device that can communicate normally (using...
Hello,
Most of the outputs and LTE Monitor use by defaut an UART on DK. Problem on custom boards, for cost limitation, UART is not always present. Probe connector is so...
irq init as below:
I use port event, and muti-gpio irqs. Irq gpio connect a sensor`s irq pin.
I detect irq gpio level in irq_Handler(), high level is my need, the...
Hello All.
I Need help ... first time use "nRF52840"
Goal of this project is "record voice with digital mems mic and play that voice using speaker with i2s"
First...
Searching through the forum I found this guide.
"Getting started with Nordic's Secure DFU bootloader, a step by step guide"
https://devzone.nordicsemi.com/nordic/nordic...
SDK 16.0.0
nRF52DK
ble_app_hts example
The ble_srv_is_indication_enabled always return false no matter in the ble_hts_is_indication_enabled function or in the on_cccd_write...
Hi, im usinh SDK V 15.3
i was following the tutorial to add buttonless dfu to my application code
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am a newbie and need some help deciding the path to perform the following requirement. Any help is appreciated.
Requirement:
I have Rigado BMD-350 module currently...
