Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
What I did was creating a timer and reading the temperature/humidity data from a DHT22 sensor in the timeout handler for every 2 seconds. Everything is fine with the data...
I have successfully created the model and i have added the model using access model add function
now i have an error in check_tx_params. I tried to use
dsm_address_publish_add...
Our BLE app (based on ble_app_uart, example) on NRF52832 normally enters sleep by sd_power_system_off(). So this works as expected.
However, if we load the app by secure_bootloader_ble_s132_pca10040...
Hi,
We are using NRF 15.03 SDK and used NUS application for the project. We need to store some data into flash and we are using FDS example based code to do the same.
...
Background
I am attempting to build a system in which a Nordic NRF52840 SoC, is connected to a mobile app (iOS / Android) via BLE and both devices play back audio-visual...
Hi all!
Resoldering usual QFN packages with pins along the edges is not such a big problem... but how is this usually done with devices they have pins underneath the package...
Configuration: 52840 / S140 / V610, SDK 15.2
As approaching production, I am continuously testing S140 on various environments.
I noticed during testing that there are...
I got Thingy:91 and want to install at_client to it, but it doesn't work well.
What I did is
1. Check out a pull request and update firmware referring to this link ...
Hi everybody,
I work on custom board with the SDK 15.2.0 and the SoftDevice S140.
I work on the ble_sdk_app_template example. I tested it on the nrf52840 DK and it work...
Hi,
I am a beginner in nrf52840 DK. I am trying to run TCP example. I have flashed client example in the DK and able to connect to the laptop(LED_2 ON). When I press BUTTON_1...
Hi There,
This is Particle's Sr. Hardware Engineer, Ping. We are working on a SoM (System-on-a-module) called EG91-SoM that with a nRF52840 (Thread) + EG91 module for acting...
Hello,
Hardware: NRF52840, Development Software: any
I am hoping to generate 3, or ideally 4 separate (independent duty cycles) PWM signals at a frequency of at least...
I use sdk13.0,s332,when my system working,it will auto reset about 129 seconds per time,I make a breakpoint,find it caused by "softdevice_fault_handler",when it reset,the...
Hello,
I am starting development on what should be a straightforward application using the nRF52832. It is actually this BLE module , which contains the nRF52832. However...
