Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello. I have 2 boards with nrf52832. I want to make 1 of them peripheral and the second one central. So the central board will connect to the peripheral board and send data...
I try launch example Nordic UART and get error: Error 133 (0x85) GATT ERROR
I need use stack for nRF51822 without external 32KHz crystal.
Here -> softdevice work with...
Here I am working on NRF52832 + SDK15。
I have designed two board with different 52832 package ( N52832-CIAAB0 and N52832-QFAAB0 ), I have disabled all peripheral part and...
I am using nRF51822QFAA & S120(v2.1) & SDK10.0.0
The application is to scan nearby ibeacon and send the ID information by UART. But the application always hang / reset...
When the nRF52 micro-controller is programmed through batch file i.e. nrfjprog utility, the flash fds fails to initialize.
Every time, flash fds initialization fails, I have...
Hello,
I am new to BLE as a technology and have a question regarding how Peer Manager handles bonding.
As I currently understand, the function of bonding is to enable...
I want to turn on the LED in Thingy:52 in a particular color if a particular condition is satisfied. How can I address the LED and turn the LED on in the desired color in...
Hi,
I am using the UART exmaple as a skeleton code to get RSSI from a peripheral nRF52 DK. I am working with the SDK V14 and I want to integrate my code with an arduino...
Hello, Nordic engineers. Thank you so much for spending your time solving my problem.
Currently, a custom board is made with the Nordic nRF52832 chip. As I have studied...
Refer to this post ， I did the same job to change simple_on_off model into generic OnOff Model , and I could control the LED state with nRF Mesh application as well.
I have...
Hi sir,
we used nRF 52832 ESB protocol ，
use
NRF_ESB_PROTOCOL_ESB_DPL
#define NRF_ESB_MAX_PAYLOAD_LENGTH 128
bitrate = NRF_ESB_BITRATE_2MBPS
so how can I config...
My app (S130 SDK12.3; BLE with multiprotocol support where the radio session is opened before advertising) registers function sys_evt_dispatch() as per
but sys_evt_dispatch...
Hi,
I am not yet familiar with NFC and have a question about using NFC with the nRF52.
If I understood it correctly the nRF52 is a "listening device" i.e. it cannot...
Hi Nordic,
I am trying to do a time critical data acquisition in a BLE based application.
Earlier I was using software timers. But, since the software timers are not accurate...
Hi all, I have some question for ask :
I add NUS service into light switch proxy server example. And I only run nus service part (Don't run Mesh part)
when I use IOS to...
