hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
In SDK 15.0.0\modules\nrfx\soc\nrfx_irqs_nrf52810.h, at line 65,( link ) it defines a SPI1 compenent:
But 52810 spec( link ) mentions only SPI0.
Is the code file correct...
Hello everyone,
So I'm trying to maybe start get going with the NRF52832 platform but every time I try I get stuck with it.
In this example I'd like to use different...
Hello, I would like to know if there is there a "global" sdk_config.h file which has #defines for all modules? Ie, if I make my own project, and use this file, all I would...
Hi!
I would like create my own application of BLE Mesh on nRF52832, I had gone through the Light switch example and understood some basic concepts and now i'm thinking start...
Hi,
I tried to erase the bound and start another pairing procedure without rebooting my device. I was not able to remove the bond correctly. The system hangs when I call...
Hi,
I had Completed secure OTA in my custom board (RL nRf51822 A1).
We have to PCBs. 1). Old Design 2). New Design
1). Old Design: We have connected relay on pin(p6...
Hi all,
In our program calling app_usbd_cdc_acm_write() a single time does not directly send a message to the terminal program (Teraterm). Even Teraterm is not getting connected...
hi, everyone:
I want to use the experimental_bootloader_secure_serial to update firmware with UART, disable the hardware flow control.
how to reset system when application...
Hello,I have couple of nRF52832 boards,nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I want to test the light control example,but some problem bother me.
It can not work normaly.The...
Any chance someone have develop a iOS (Objective-C / Swift) library to wrapping Nordic DFU Protocol?
I'm aware of the availability of the source code of nRFToolBox ( github...
When is the next version of nRF52840 coming out (or available through a distributor in Switzerland)? In an earlier version of this chip, we were unable to link the micro USB...
After setting up the tool chain and confirm it is compiling correctly by flashing the Proximity build into the dev kit PCA10040 and confirmed with the Android App it is fully...
Hi,
I am develope a ble device use nrf51822 , when I use a Android app to connect the device without start a scan , only use the mac address to connect the device , I cann;t...
