There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I am working with the ble_app_uart (central and peripheral) example and they already run fine. Now I discovered that some button actions are already defined on the...
Hello,
I have created the simple software usign NRF51DK to make the led blink for 5 times by using while loop
just to make the other part of my software
my aim of this...
hi，i have a question.
i set the advertise type to BLE_GAP_ADV_TYPE_ADV_NONCONN_IND MODE, and i add scan response data,but i can't see scan response data.Why?
Hi,
I would like to connect nrf8001 to a Renesas microcontroller but I could not find any documentation on how to proceed with this step. The only documentation I could...
The ADC module requires that the output impedance of the connected voltage source be 1kohm or less (section 31.1.3 of RM).
Does the same restriction apply for the LPCOMP...
Im having some issues with my nrf52 DK board, the jLink firmware seems to be buggy, I installed the latest available (160212) manually, but the j-link tool keeps bugging me...
SDK 9.0.0 sd s110
I want bootloader to store some persistent data at the APP DATA location. while going through the bootloader(dual_bank_ble_s110) source code, i noticed...
I have never worked with BLE devices before. Now I have a BLE project where I must be able to do he following:
I want to be able to pair/bond my BLE device to a smartphone...
chip N51822QFAACO
s110_nrf51822_5.2.1_softdevice.hex
keli 5
\nrf51_sdk_v4_4_2_33551\nrf51822\Board\pca10001\ble\ble_app_proximity\
works fine
nrf51_sdk_v5_2_0_39364...
Hello Everyone
I have designed my custom board using nrf51822 i have tested the votlage rating, on the VDD pins everything is fine (3v) but the real problem is my antenna...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hi,
I think there is the bug in SDK11 Spi slave protocol. After a msg is received from the SPI Master, I notice that the spi slave event always have the rx_amount and tx_amount...
Hi All,
I noticed these serialization FW with huge amounts of code in the makefile.
What is the core functional difference between any example with and without serialization...
