Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I am trying to change analog-to-digital (SAADC) sampling interval when sampling using Easy-DMA in nRF52832. The code looks like follows (error checks removed for clarity)...
Hello everyone,
currently I'm working on a project with an NRF51-SoC. I want to use a MEMS Oscillator as high frequency clock source this is working very well so far. But...
I have 500 nrf51822 devices, when I use Master Control panel to scan twice, the first time I can scan device A, the second time I can not scan out device A.
I google find...
Hello,
My understanding is that you can use the nRFToolBox app to upload code using OTA DFU.
But this looks cumbersome, as you have to first get the hex file on to the...
I built the ble_app_uart example app using GCC with nRF5_SDK_11.0.0_89a8197, and on testing it with the latest version of Nordic nR ToolBox (iOS) and nRFMaster Control Panel...
Hi,
I want to save settings in the memory.
In my case, the softdevice is enabled, there is no ble advertising.
I use pstorage functions.
Problem: I stored 0x12, 0x23,...
Hi,
I'm running a nRF51422QFAC and using sd_temp_get() to read the chip temperature twice / second.
I put it in a temperature chamber and swept the temperature from...
Dear members!
I followed the tutorial of the nRF8001, and tried this code: learn.adafruit.com/.../nrf-uart-in-detail
It worked for me just fine, but...
I have an...
Hi there,
I'm attempting to use the UARTE for a continuous read scenario but I am noticing there is significant delay between the STOPRX task and the ENDRX interrupt (...
Hi,
I'm trying to get a custom PCB working. I can use either the plain peripheral UART, or the ble-app-uart example projects on the NRF52-DK and they work, but they don...
I am using the nRF52 Preview kit (PCA 10036 board) and SDK 0.9.2. Up to this point, I have been able to do everything I want with TWI using the hardware driver. This time...
I tried measuring idle current for nrf51422 board and got something about 1900 uA using multimeter without resistor and with bridge SB9 cut. I know the value is too high....
Dear all:
error occured when I was programming application hex in nRFgo Studio1.20.0,just refer to "program application error.png" ,the error shows "programming failed...
I have a sensor device that needs to transmit every so many seconds. I am looking for a code example to run on nRF52-DK that will do this, sleeping inbetween transmissions...
