hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello.
I want to flash DFU bootloader with keil on chip nRF51822-CEAA (256kB flash, 16kB RAM). I'm using s130
The areas i write to are:
IROM start: 0x3C000
IROM...
I was wondering if it would be possible to add an event for Service Discovery (and other similar BLE stack events) that could be detected by user applications. Per answers...
hello there i have two nrf51 dk kits. now i want that one act as central and other act as server.
i want to communicate between two. can you tell me how to do it??
i think...
hello all:
IN s310 multiprotocol--ble_ant_app_hrm example ,I open the macro BONDING_ENABLE, then i compile,there is a error
......\main.c(674): error: #136: struct ""...
Hello,
At the moment, we test the “Power Off” Mode for lower energy consumption of the nrf52 Preview Developement Kit (V1.0.0) in our project and I have a question about...
Hi,
Does anyone have some simplified DFU code for IOS/Xcode they are willing to share? I am looking to integrate DFU functionality into our app. I looked at the nrfToolbox...
We are a small start-up developing low volume product and paying 2500 USD to Bluetooth SIG for listing our BLE device in their EPL is too expensive for us. Is there any option...
I'm looking for a way to let my device "nrf51822" to be connected only to my own mobile app.
I'm wondring if you have already a Nordic solution that I can use ? (tutorial...
Hello friends,
I'm having MDBT40 EVB which is cheap one as compare to other but with lack of build and debug support. But i dont know how do i flash my hello world blinky...
developer.nordicsemi.com/.../a00935.html
The doc seems to provide only write functions.
And, the flashwrite example doesn't show how to read from flash even after device...
Hello,
I am currently looking through my error handling and noticed that there are some errors that I do not really understand fully, so I've summarized them here:
0xDEADBEEF...
Hi,
I am trying to make a communication between a nRF51(uESB) and a nRF24(ESB). The uESB uses tx_payload and rx_payload as buffer to send data. Bytes 0 to 4 are used for...
Dear Nordic team,
I've seen very much reproducible crashes of your Android nRF Master Control Panel app when trying to see details (button "MORE") of particular Peripheral...
Hi Nordic,
Is there a way to follow blog posts the same way as standard questions? I haven't found anything and it's really painful when you want to follow discussion or...
From bLE RF sniffer user guide:
To set up the Sniffer you will need one of the following pieces of hardware:
• nRF51822 Evaluation Kit (PCA10001) and a mini USB cable...
