Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I occasionally get an NRF_ERROR_NO_MEM error when trying to add a custom characteristic. I'm only using 3860 bytes of ZI data, stack = 2048, heap = 2048 so it seems like I...
Hi
I am working on the ble_central_and_peripheral example in nRF51_SDK_8.1.0_b6ed55f .In this example it is possible for us to connect to 3 peripherals only.But we would...
Hi, are there any examples in C for how to directly access the registers on the chip? I realize this is a super basic question, but all the register access in the examples...
Hi,guys
I set BLE parameters like this:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL MSEC_TO_UNITS(1000, UNIT_1_25_MS)
#define...
Hi,
I'm using sd_ble_gap_connect to connect to a set of known address and whitelisted devices. My central periodically (once an hour) needs to check on a known set of devices...
Hello,
I'm looking for electrical parameters in nRF52832_OPS_v0.6.pdf but I didn't find typical impedance values for analog inputs .
Also not found any value for RESP and...
Suppose I defined services (According to nAN36 Document)
#define BASE_UUID {}
#define SERVICE1 1602 // This service send a alert message Id i.e. similar to proximity hex...
hello,
I am working on the example ble_central_and_peripheral in nRF51_SDK_8.1.0_b6ed55f.I can connect the device to master control panel in the computer and discover services...
Hi all,
I am trying to update the bootloader, softdevice and application all in a ZIP package through DFU, and at 99% after upload it stop and throws the error:
...
Dear Engineer:
I am a developer of the nRF51822;Some costomers want to send a large number data over the bluetooth,So they require a high quality in speed;I want to know...
Hello,
I've noticed that it is quite hard to set up an Eclipse development environment and I want to try to make a package of everything that is needed for developing with...
Hi. I want to attach a sensor with SPI slave interface to the nRF52 Preview DK (PCA10036) using the SPIM1 with EasyDMA. Below I have two related questions:
In PAN...
