hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I am using TIMER2, GPIOTE and PPI to implement a 6250Hz square wave at a GPIO pin. I can successfully create the square wave on the GPIO pin. However, I would like...
Hi,
I want to use nrf51822 for implementing HID keyboard and mouse.
Can the application be configured for keyboard and mouse simultaneously ?
i.e hids_init_obj.is_kb...
Hi,
I am using nRF51822 and trying to use Ticker from mBed library.
I have issues when using Ticker and PwmOut.
How is implemented the Ticker functionnality into nRF51822...
Hi,
I want to make a pulse for buzzer and led.
I find a sample source(led.c) and the Nordic SDK.
It is good enough in case posivie and negative duty is same.
I need...
Hello ,
As mentioned in another question, I would like to use the nrf51822 SPI slave peripheral to benefit from the DMA capability although I want to behave as an SPI master...
I can't seem to find where/how the BLE address gets randomized so it changes periodically when using the BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE address type.
-It seems...
Are the OVERRIDE parameters useful in any way shape or form when using the NRF_2MBIT mode?
Is there any reason other than BLE compliance to use the OVERRIDE parameters...
I cannot uninstall MCP on my W7 x64 system using the normal control panel add/remove programs method. It appears that I need to re-run the original installer which I no longer...
Hej,
that might sound like a dumb question, but what is the minimal setup to program an nRF51822 SoC using the SWDIO/CLK ports?
What external hardware is required...
As nRF51-DK User Guide said: "If you have swapped to the mbed image and want to revert back to the J-Link image, download the latest SEGGER J-Link software from www.segger...
I have bought the Beacon Kit because it matches my needs in terms of PCB shape and size, I have Evaluation Kit as well and use it for debugging purposes, but would like to...
I want to know the time range of advertise timeout.
Why it doesn't work if I set the time to 360 seconds?
It can work if the time less than 180 seconds.
Is the range 0...
Hello,
I would like to develop an application that makes photos using a small camera from the omnivsion series and send the data via Bluetooht, using the nRF51822. These...
