Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello, sorry if this is a stupid question, but i'm fairly new to BLE (nRF51822), and even newer at report descriptors.
I'm using a nRF51822, SDK6.0.0 and S110 7.0.0.
In...
I saw softdevice no memory every several times, according to spec, softdevice use 8k, and app use 8k, are they share this 16k memory or no sharing, each use 8k, and reduce...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
My PCA10001 was working(running the heart rate monitor example) from the coin cell. After it ceased to work, I assume the cell was flat, but on replacing it the PCA10001 still...
Hello,
i'm trying to get running nRF51 on Arduino IDE. I have forked RFduino at the moment github.com/.../RFduino
With SDK i can compile a startup library and an simple...
I am having a lot of trouble using the new 4.3 Android API. I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I have...
Hi,
I'm using a 51422 with a s210/s310 softdevice. I have some nodes that must exchange some independent data. So I configured the communication to be an independent bidirectional...
Hi,
I am using SDK6.1 and SD7.0 for our application. I would like to know how to implement the static PIN type pairing?
I have searched Nordic's developers zone and found...
Hello,
I am new to nRF51822, and trying to make a simple application for master - slave data transfer.
I want to know how Much time passes from the start of the device until...
i want to prevent somebody to copy my app by SWD interface,so i set RBPCONF register in main application,but i find that it is no use writing RBPCONF register.
First ,i write...
Hi all,
I am new to nRF51822, and trying to make a simple application for device-to-device data transfer.
I have tried the "ble_app_uart" example, which is for device...
I compiled a new HEX for the pca20006 Beacon based on the ble_app_uart project for the pca10001 (remapped the LEDs and buttons), but when I load the beacon using OTA DFU,...
I compiled a new HEX for the pca20006 Beacon based on the ble_app_uart project for the pca10001 (remapped the LEDs and buttons), but when I load the beacon using OTA DFU,...
Hello all.
I just finished started setting up the environment for Nordic development. We have a Beacon Kit and a nRF51822-EK board.
I managed to compile and run board...
