Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
our company one new product using you nRF52832. We already prepared everything for CE (RED ) and FCC certification process. Only thing that is unclear is Bluetooth SIG...
Hi!
I am currently using SEGGER Embedded Studio version 4.12, nRF5 SDK version 15.2.0, nRF5 SDK for Mesh version 3.1.0, Hardware BMD-300 Evaluation Board.
i using the...
I need to measure a load-cell bridge. Although, I'm fairly certain I'd be better off with an external delta-sigma ADC with an internal amplifier - I'd like to run through...
Hi,
I study on Thread resently.
I found it is not any output in the Debug Terminal Window when using NRF_LOG_XXX, but the J-link Control panel showed the logs.
Here...
Hi,
I am trying USB DFU trigger.
I have connected GPIO P024 to Reset port P018.
Bootloader is also programmed.
When I use nRF connect/programmer.
It's always waiting...
My system: MacBook Air with macOS 10.14.6, Xcode 10.3, with sdk at /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.14.sdk
When...
Dear nRF52832 experts,
I have a SPI slave device which can periodically notify the MCU with data ready (DRDY) signal. For each DRDY signal, we should perform a SPI transaction...
Hi there, I am developing a mobile solution using BLE. Actually I use a sniffer based in IC nRF51822 and Wireshark + nrf sniffer as a tool for traffic capture. Sometimes,...
Hi,
I have similar problem to what is described here .
My situation: 1. I connect 2 PDM mics to the board (CLK is pin 27, Din is pin 26). 2. I connect a couple of TWI...
I was wondering if there is any way to setup a callback when data is received on an open socket, as opposed to just regularly polling the socket?
The application I have...
Assume a BLE connection has been established between a master and slave. The device in question could be either the master or the slave (if it matters).
I have an application...
Hi, when using fds_record_iterate() to iterate over records, it only returns the record ID, but not file ID or record key. Only after opening the record you get the file id...
The nRF52810 datasheet shows the EVENTS_COMPARE register as RW, so I'm assuming that I can write to it.
But when I write to it, nothing happens.
Example.
I set up...
