Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello,
I don't understand why the ble_advdata_short_name_find function never return a true value. I'm sure that I send a short name because I verified this on the nRF connect...
Hello, I want to synchronize several peripherals with a central, I already tried to do it with the state of the gpiote but I did not have the expected result at the level...
Hi
I'm facing a Hard fault on the softdevice when trying to call sd_ble_gattc_write(). SDK15, SD140
I have a Multilink central connected to UART using app_uart. when a...
I have been doing a bit of searching and reading but I'm none the wiser.
I have a client that uses lots of BLE nRF51822 based modules made by Raytac Corporation in a classroom...
I am converting Arduino BNO080 library ( github.com/.../SparkFun_BNO080_Arduino_Library) to nRF52832.
Specifically, this is a function for sending a SHTP packet over I2C...
hi to all,
i had developed a device with NRF51822 wih S130 and i want to port my application to new NRF52840 soc S140 and SDK15, S130 has an structure that let me to limit...
Below are the symptoms, but it turns out the problem was quite simple: the device is not seem capable of scanning while at the same time being connected, unless you use a...
Hello,
I have a problem where the nRF52840 is not advertising. The code runs in the debugger but there is no radio signal. I've already sent the schematic and layout....
Is there an easy way to check what the current connection's agreed upon MTU is?
I'm connecting to random devices that all have different intervals and MTUs. I can't be sure...
When I use saadc to sample battery's power,the software restart ceaselessly.I use the steps as following:
1.void saadc_init(void).
2.void saadc_callback(nrf_drv_saadc_evt_t...
Dear Sir,
I am now using nrf51422 module (SRU532) for ANT+BLE application , i have used SDK_9.0.0_2e23562 and soft device s310_nrf51422_3.0.0. The problem i am facing is...
Hello,
I am using SDK 12.3.0 on nRF51822 development board and nRFConnect app to scan and connect the peripheral device.
When i changed Mouse icon by the GENERIC_THERMOMETER...
Hi,
I'm developing a simple software that records RSSI values from both the Central and Peripheral device, using nRF5 SDK 15, adapting from two of the provided examples...
I am trying to implement the example-code for the Eddystone example from the infocenter. I'm using the nrf51422 to flash code to the Smart Beacon (PCA20006 with nRF51822)...
I am using the Nordic 52840 CSP for my project. It is used for a asset tracking application. I used the nRF52840 QFN schematic reference for design. Since there is a difference...
