hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi Support team,
I am looking to replace my BLE chip by a nRF8001. I am currently using a DA14580 (Dialog Semiconductor), in Beacon mode or pairing mode. I saw that the...
Hi,
As given in the link: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools%2Fpower_profiler_kit%2FPPK_user_guide_Troubleshooting...
Hi, would you support with the following:
In the high voltage mode (defined as when the supply voltage is only connected to the VDDH pin and the VDD pin is not connected...
(Overview) When accessing the I2C device connected to the Nordic controller nRF 52832, The CLK frequency changes during the process, resulting in operation at an unintended...
I have the nRF52 Dev Kit running now on Mac OS with SES.
(for reference to this topic: click here )
My end result is to use the nRF52 chip as part of a MIDI wind controller...
Dear All,
I am looking for EMI/EMC testing for my custom board based on nRF52832 board. Could you please provide any generic firmware for the same. Is there any UI to test...
Hi
I have my application running on nRF52 on SDK 11 (Softdevice S132 version 2.0). I am using 1 peripheral and 6 central links in my application. I am migrating the application...
HI, i have a small question. When I downloaded the hardware files of thingy52, and opened altium files, I can not move components in a pcb layout, i have to split windows...
Hi,
To decrease the load on the system I would like to periodically send some BT data (and do some SD card writing).
Since Timer 0 is used by the soft device, I am using...
I want an amplifier to receive audio from a FM/DAB receiver and from an NRF52832 that - in turn - has received audio over BLE. The amplifier should either receive the radio...
when I start to program nRF52832 under 1.8v some memory pages can't be accessed. this is short listing:
Erasing page at address 0x78000. Erasing page at address 0x79000...
Hello,
I'm trying to make some current measurement using the nRF6707 and a nRF5 SDK Board(10040) (Board out of the box, shunts untouched).
We're facing problems measuring...
Hello,
Does the newest SoftDevice release v5.1.0 support the advertising data length extension (255 bytes)? If not, will it be available this year?
We are at the evaluation...
Hi,
I am using nRF52832 DK (PCA10040) SDK 14.2.0 and S132 V5.1.0.
I am planning to test the TWI loopback (in order to familiarise the APIs used for TWI in nRF52).
I...
Hello,
I want to update the connection parameters once the nrf52x (peripheral) is connected with the android (master). I tried the following:
In connection event i called...
