When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi，
i defined spis rx and tx buffer length at:
#define HUB_SPIS_RECV_BUFF_SIZE 1024
#define HUB_SPIS_SEND_BUFF_SIZE 1024
because the rx data length will be vary...
Hello nordic
I use ble to create custom services, I want to create an embedded system that can create and send and receive data. I am using sdk version 14.2.0 and what...
Hi,
Im currently designing a custom pcb using nrf52 reference design available here . In my design, I have to connect the ground of two analog signals to VSS of nrf52832...
I tried Blinky blank application on PCA10040 by IAR. By pressing "Download and debug", everything is fine, I added RTT debugging information and can see it from RTT viewer...
I Have an issue trying to flash a nrf52832 custom board.
Something extrange happens because when I download an example from keil that blink a led(gpiote_pca1036(nrf52 PCA10036...
We are using s110_nrf51_8.0.0_softdevice.hex soft device and nRF51 SDK v10.0. We have below questions in case of soft device assert scenario.
In what scenario's soft...
Hello,
I am working with the example of PDM example on the nRF52832.
And over this I would like to use the drv_speaker. I put all the files from the Thingy 52 example...
On a system using an NRF52832 with S132 softdevice (without no external LFCLK XTAL), in low power mode via sd_app_evt_wait() - we see a nominal current of ~3uA with a periodic...
Hello Nordic,
Can you share pdf of nRF91 sneak peek presentation.There is an audio problem on video.
Best regards,
Marcio
www.nordicsemi.com/.../Low-power-cellular-IoT...
hi team,
i am having a doubt. i had created a service for connection interval which is 0x1528. with read and write properties. in that we can set value from 100ms to 10240ms...
I would like to ask for any information regarding the near-future plan for the nRF SDK for Mesh.
Are these features planned? And if so, when would they be implemented?...
nRF52832
There are three ways of working with the clock registers, a hardware access layer macro set, the nrf_drv_clock.c/h, and direct register access.
What is the...
I am implementing Device Firmware Update using BGLib on C# using BLED112. When i am writing on the DFU Data point on Peripheral (which is a Nordic's nrf51 chipset), i need...
hi,everyone.
version:sdk10.0
i know the nrf51822 system running order is: softdevice->bootloader->app.But i have a question when i am reading bootloader. If the program...
I have a question about the wait_for_flash_ready routine in the nrf_nvmc.c file.
static inline void wait_for_flash_ready(void)
{
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
