hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi everyone,
We have one weird problem with loading the program to the two different variants of nrf51822 chip via nrfgo Studio. We would like to change nrf51822AA chip...
Hello,
We need to extend both "ATT_MTU" and "Data length extension (DLE)" of the example programs "app_uart" and app_uart_c" in S132 SDK 14.0.0. So could you please advise...
Hello,
I am using sdk 12.2.2 and pca10040. I am have successfully interfaced bme280 sensor with nrf52. Now I am trying to interface bmi280 with nrf52. So for that I need...
Each time we wake up our serial port we call APP_UART_FIFO_INIT because we want our buffers to be cleared when we wake the serial.
Does this also overwrite the PIN_CNF register...
Hello,
First of all I know that many questions were posted here about this topic but I am posting mine because I couldn't figure out how to solve my issue and I am looking...
I have a custom service that on a event needs to be re-initialized. The custom profile also has DFU. It seems that when I re-initialize services_init() the micro crashes on...
Hi,
I need to support two advertising protocols simultaneously Beacon and iBeacon.
This is because iOS.CoreBluetooth has a lot of limitations (there is no way to identify...
I want to know OBD-II Application scenario
ignore how to get OBD-II information from the car. assume I already get the info
generally, how often fetch the information...
Hello engineers, Recently I test the ADC function,I think the library function is so difficulty for me. So I want to use the ADC by register,but I found that ,after I start...
I am developing on a nrf52 board with a fdc2214 chip. I created 1 custom Service and 3 characteristics shown below, and the format of my UUID is 0000xxxx-1212-efde-1523-785fef13d123...
Hello, I successfully ported one provisioner and one provisionee to 2 nrf52840 experiment boards respectively, now I'm having the provisionee connected to my computer and...
Hi, I asked a relevant questions before and was advised to solicit such information from my local Nordic operations. But they didn't appear to know that either, so I'm here...
Calling ble_nus_string_send() from within a TWI callback (case NRF_DRV_TWI_EVT_DONE) is performing a reset on my PCA10028 (nRF51422). It works fine from the main loop.
...
When I run nrfutil, the program immediately throws a Python exception. It has been working for the last 6 months. I've used pip to try to upgrade protobuf and nrfutil, but...
I AM HAVING A COUNT VALUE WHICH IS IN THE RANGE OF 10000 - 100000 WHICH IS TO BE TRANSMITTED OVER THE BLE (OF THE BOARD) TO THE ANDROID DEVICE. I like to use nus service to...
