Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I have been struggling with Eclipse for a couple of days. I created the pwm_driver project via the File/New/Makefile with existing code option. After initializing...
I'm trying to run the DFU buttonless example however this line crashes the app:
err_code = ble_dfu_init(&m_dfus, &dfus_init);
UPDATE:
Looks like this is causing the...
Hi all,
I am learning about the security mode level in BLE. Understood that BLE 4.2 added additional method which is called numerical comparison.
When I tried the...
I am searching for example on pstorage, I want to store data in flash using pstorage, mainly I want to know which files I need to include for using pstorage.
Hi all,
can we configure systick on nrf52840 to genrate exception every 1msec.
Tried doing the same but not able to observe correct value.
These are my configuration...
Hi. I need high data transmission rate(>500 KBps) over a long range(about 1000 m). Can you suggest me the best device according to my req.
Thanks & Regards
Utpal
Hi,
I have configured systick for 1msec value with Ticks=64000. When I read the systick calibration register value, the value is 0xc0000000. This indicates the Tenms register...
Hi,
is it possible for the NRF52832 to have an external I2S MCK clock when being in master.
Because I am working with a DAC/amplfier which will play some sound files from...
Hello.
I'm newbie in nrf51 world so maybe my questions will be a bit stupid.
I bought few nrf51822 modules on Aliexpress. Photo: www.dropbox.com/.../77_1.jpg
I bought...
Hi,
When trying to install nrf5x Command line tools 8.4.0 (under windows xp), the setup program ends with an error (see nrf5x-cmdlinetools.log ).
It seems to do with...
I want to be able to read my i2c and program logic flow within the BLE application but when I try to set breakpoints it causes the cpu to do a hard reset. How can I capture...
I have an nRF51822-DK board and so far I could not properly grab from the examples a simple thing: is there any specific initialization needed when coding?
For example...
Hi All,
I'm currently developing a network where I would like to use nRF52 SoC. The nodes in the network must be able to extend to over 100 and must be able to multi-hop...
Hello,
I've taken the example from the SDK 12.0.0 for RAM retention. I've added additional NRF_LOG statements to check if the RAM retention is happening. I do not have...
