Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello all,
I little confused with these two examples as mentioned in my question. Both examples are different and their use case is also different. Can somebody please...
Hi!
Faced such an anomaly. In 2-3% of cases when exchanging PTX device sees a transmission error (the ACK did not come) and device PRX is not see this error.
Is there...
These pins do not work when I connect to nRF51822 module directly..
Like this. I cennceted VDD, SWDIO, SWDCLK and GND to nRF51822 module.
And there are not jumpers to...
Is there any sample code in examples, because am a newbie to this great platform, my objective is to glow an led , when the motion is detected , and also when there is no...
Hi Sir,
I add NUS service into CSCS project base on nRF5_SDK_13 follow the steps below, there was no error occurred after build the project, but it didn't work. Please...
Hello,
I'm trying to set up I2C with an mCube cccelerometer, which has an I2C 7 digit ID of 0x6C and an 8 bit address (write) of 0xD8.
With the code below, I see on...
Hi.
I have a custom board, which I power up via AAA battery through a buck-boost converter. I wan't to measure battery level using on-chip ADC only on requests from master...
Hi there,
I've successfully sent the experimental buttonless dfu app "over the air" but now I am no longer seeing the option to DFU from within Nordic Connect.
Must...
Hi,
I'm using a PCA10040 board with the UART example provided with the v12 SDK, and the data seems to get corrupted somewhere along the way between my Ubuntu machine and...
My app works well when working with Master control pannel, but when I use nRF Connect (Android App of Nordic) I have a disconnection without any reason. Especially when I...
I want to send some data more than 20 bytes.
I use
ble_nus_string_send(&m_nus, tx_stuffed, 10);
3 times.
In the advertizer.c
in the function on_ble_evt
I insert code...
Hello,
I am trying to get to the bottom of a double-reset-problem which I am facing, whenever I flash my software-program to the nRF52832 (1 for the flashing and 1 after...
SDK Release Notes:
nRF5 SDK v13.0.0
Release Date: Week 11, 2017
Highlights:
Implemented a new license scheme for the SDK distribution. See the
documentation...
HELLO,
I want using sdk5.2.0/s110 6.0.0 update app in app.I only find BootLoader->app.How can I achieve it.
eg:I use my phone connect 51822 board,then send a command to...
