Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi, I'm working on a cross-platform application that needs to communicate with a custom peripheral (nRF51822 with S130 v2.0.1). I've implemented the interface for both Linux...
Long time reader first time poster upper.
I am working on a very minimal BLE send / receive scheme for a research project, and am not using a SoftDevice. I have written...
Hello,
I am noticing something curious when I attempt beacon mode for my nRF52 (sdk 12.1). Attached is an image of ubertooth packets that correctly show my ADV_NONCONN_IND...
Hi,
I am trying to communicate to PCA10040 (nRF52) dev board to communicate.
Basically i want to configure 1 board as Master another as slave, so master will initiate...
Hi,
I am using SDK 11.0 for my project development. When I tried to compile the unaltered SPI example given I got 60 Errors in my laptop. The Same SDK in other laptop is...
Hi all,
first of all I'm new to NRF and BLE applications so I'm truly sorry if some of my questions are very basic and if answer to some of them is already posted somewhere...
Hi all,
I am using pins P0.00, p0.01, p0.09 and p0.10 in my application. I wandering why these pins are not functioning as GPIO. I have searched various links such as ...
Hi，everyone！I am using nRF connect mesh for Mesh DFU(see this link text ), and I follow the direction step by step. But, the nRF connect can't find any device to program....
Hello,
I am trying to implement a Heart Rate Monitor Interface (HRMI) board with my nRF52, using the TWI_sensor example from SDK 12.2. I am running into trouble Writing...
Setting up an example of the problem
As I promised in this thread , I have been testing out the ADC on the nRF51822 and trying to see how quickly I can sample per minute...
I'm using FDS in SDK 11.0.0 on a nRF52832. I was having some trouble with freeing flash storage and after doing some research I came across this post and I applied this patch...
Hello,
There is a bug in pstorage.c from SDK which can cause that module to fail to complete a flash operation. The problem is that the pstorage_sys_evt_handler function...
The product spec says "This event will also be generated if the supply voltage is already below VPOF at the time the POF is enabled" but it seems like the event is not generated...
I have a BLE device that is using Nordic SDK 8.1 and uses PWM to control an LED. Now I want to turn the led off with PWM. To do this I set the duty cycle to 0 and printed...
