Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello all
If you could please point me some directions on how to solve my issue, I would be grateful:
Some background info:
SDK used: 9.0
spi master code =...
Dear Nordic Developer Zone,
I have a silly question. After searching in the Nordic and Bluetooth documentation, I didn't find what CCCD and SCCD mean. Theses metadata are...
I had a design on 4-layer PCB with nrf51822, then the requirement was changed, then the 2-layer is sufficient for routing.
But I thought 4-layer PCB is better for RF circuit...
I've run into a problem with an OS API call when running FreeRTOS on an NRF51 due to how ticks are corrected.
vTaskStepTick() is getting called while the MCU is awake and...
Hello all,
I am trying to activate ADC to measure a voltage every few seconds using nrf51822. When it is done, I supposedly deactivate ADC so it does not consumes while...
I am designing an device and i need to communicate with the device using the I2C of my nrf52.
when ever i try to initiate the transfer process using the driver function...
Is there a Peripheral Encryption Example for the nRF52? and can the Master Control Panel tool(3.10.0.14) be used to test the Peripheral Encryption?
If i clcik the down arrow...
Question about usage. I am using the nRF52, and ported product code that was running on the Alpha SDK11 to the release SDK11. I believe that what I will describe is a new...
According to the product specification of the nRF51422 the current between the advertisements is:
i_sleep = I_on + I_rtc + I_x32k
16k Ram enabled: = 2,6 µA + 0,1 µA...
I realize that this code is "experimental", but we are trying to utilize it as a reference and having problems with its stability and scan results.
Specifically, we are...
Hi!
We are currently implementing a time synchronization algorithm using a nRF52s. Currently, we´re getting the min error of 20ms between synchronized slaves. We think that...
I'm using a nRF51 with 32K RAM and SD120. When I started using RTT Viewer I could send data to the terminal, and debug my code. Recently my J-Link plus won't allow me to debug...
I'm trying to secure my peripheral by allowing only bonded devices to connect. I'm using device manager, when I bond a central with nrf master control, the bonding succeed...
Hi,
I'm facing the following issue when trying to use the DFU bootloader. Below you can find the code of the bootloader, which I flash after I erase everything, flash S110...
hii....
i want to make my device connected through a secret pass code (may be six digit)..ie. my device get advertise then when master control panel discover my device...
