Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
i have a bunch of nrf51822 hwid 0024 or 001E.
With softdevice s110 version 7 everything worked fine, but starting with 8, they pretend to work fine (no error codes...
Using the pure-gcc makefiles, at present I only see this for a stack trace in the command line gdb client:
(gdb) bt
#0 0xfffffffe in ?? ()
#1 <signal handler called>...
If you have the most trivial main.c possible, with a main() which does nothing at all, compile, link and load it at 0x00000000, it runs fine and does nothing .. that's basically...
I have a nRF51822 program in which a button triggered event doesn't work as expected and crashes the program. The program may have potential race condition problem. Here is...
Hello,
I've overcome most of my problems using this wonderful Q&A system from other people. Recently I've moved from a nRF8001 + MCU to a nRF51
Using SDK 8.1.1, keil...
Hi all-
I apologize in advance for the noob question but I have spent loads of time on this and can't make progress. I am trying to work my way through the nrf51822 User...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Is it possible to add a payload (1-2 bytes) to the beacon advertising packet?
I intend place an ADC output to the payload. For now, I'm using nRF51-DK but later wants to...
Hello,
I'm developping an application using softdevice S130 with the nRF51822 evaluation kit.
The device has to scan multiple devices, and to save power, I'm storing the...
The SDK defines functions for operating on "ports", which are the output space divided into 8-bit chunks:
nrf_gpio_port_clear
nrf_gpio_port_dir_set
nrf_gpio_port_read...
As previously seen on softdevices topics ( devzone.nordicsemi.com/.../) I need to restrict BLE advertisement on only one channel for sniffing purpose.
The thing is, I cannot...
Bluetooth Smart Internet gateways (GATT)---Available early 2015 through the HTTP Proxy Service (HPS) & RESTful API white papers....
what does it mean..? is it available...
Hello,
I started to make an app for a board with nRF51822 with softdevice S120 version 1.0.1. Now I would like to have the DFU implementation in it but I am stuck at the...
