Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
Function call to > err_code = ble_advdata_set(&advdata, NULL);
returns always err_code = 7 (NRF_ERROR_INVALID_PARAMETER) for a 128 bit UUID type (BLE_UUID_TYPE_VENDOR_BEGIN...
I am using pca10001, SDK6, SD7.1.
In my application i want to send a large amount of data to central(ios).
So im sending data as a packet of 19 bytes and each packet with...
I have NRF 51 DK.
I adjusted the toolchain path to arm-gcc 4.9 2015q1. This version works fine for the NRF 51 SDK.
I get this error:
lto1.exe: fatal error: bytecode...
I'm seeing the resetreas show the CPU lock-up detected after I reboot. This error is occurring while using the ADC. What type of fault condition can cause a CPU lock-up detection...
Hey everyone,
I'm developing an application using the IoT SDK . The first part of the application consisted of a normal BLE peripheral to interact with an android app....
app_timer.h contains a useful macro for getting from milliseconds to a number of timer ticks, given a prescaler value with which the timer was started:
#define APP_TIMER_TICKS...
Hello,
May i know what will happen if we happen to assign the same pipe address for let's say pipe 1 and pipe 2?
Can we still receive data and be informed of the pipe...
Hi,
My goal is to send temperature values on the advertising so, I'm trying to get work this example, but i have an error about this lines of the code on keil:
advdata...
Hello, how can i modify the hrs_s_evt_handler() to initiate bonding only if it my configured belt address?
My Solution:
static void hrs_c_evt_handler(ble_hrs_c_t * p_hrs_c...
Hello, All.
I want to know AppID in iPhone's App using ANCS.
(for example, Facebook App's AppID is "com.facebook.Facebook",
Facetime's AppID is "com.apple.facetime")...
Hi Nordics!
I want to add custom service into ANCS example for android.
But I cannot understand how to add custom service stably.
First, I just added my custom service...
I have compiled the nRF51-ble-bcast-mesh 's examples: "LED_mesh_SDK7" and "BLE_Gateway_SDK7" on Keil uVision v5.14.0.0. But, I am facing problems flashing them on to my nRF51422...
I have a problem that I can't figure out. I have a custom board with an nRF51822 QFAB. The board will run a test application that uses nrf_delay_ms() to toggle an output pin...
Hi!
I have reviewed the NRF518 reference design, i.e., case "PCB layout recommendations for the NRF51822 WLCSP62 package" and the layout pdf files provided therein:
...
