Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm trying to use the nrf_drv_spi.c to communicate with a BL652 + MCP2515 CAN SPI custom device. I've connected the MCP2515 to the nRF52832 (BL652 module) in the following...
as others have described I run the sniffer
than go through pairing process, the encrypted packets show up as "Encrypted packet decrypted incorrectly (bad MIC)"
is there...
Hi.
currently i use the nrf connect with a dongle to connect to a ble device to read/write characteristics for testing purposes.
Now i want to do it automatically using...
Hi all,
I am adapting some examples according to my needs and have encountered something that I find strange. I am trying to send 244 bytes from computer to usbd_ble_uart...
I want to program my nRF52832 Over-the-Air but not through Bluetooth. We have a Wi-Fi chip interfaced with nRF52832 so that the device can be connected to the internet.
I am trying to read the current time using CTS. I used the example source provided by nordic. However BLE_GATTC_EVT_READ_RSP does not occur in ble_cts_c_on_ble_evt.
BLE_CTS_C_EVT_DISCOVERY_COMPLETE...
Are there any examples of sampling something like an I2C bus at a constant sample rate? I have seen issues myself with the k_sleep and k_busy_wait not giving accurate delays...
nRF5_SDK_15.2.0_9412b96
soft device: s140
Compiler SEGGER Embedded Studio
1. I have used example ble_app_uart. I connected the ble module to a device which has a baud...
Hello,
I'm looking for a little clarification on how the antenna tuning circuitry works on the Thingy:91 v1.0.0 board.
From a previous topic on the DevZone, I saw that...
I'm having an issue where I can't reconnect to a device after updating the firmware from the iOS SDK. I believe it's the issue described here in the documentation:
Since...
I am having responding to an authorized write request. It seems to work for BLE_GATT_STATUS_SUCCESS case but any time I try to set the gatt_status to an error, the call to...
https://www.youtube.com/watch?v=wa_ARkZSr_U
This video presents how Bluetooth mesh network works . As we can see this network contains nine Thingys and one nRF52 DK (not...
I am now experiencing such a problem. I packaged 20 packets of data, each packet of data is 13 bytes, and then I want to send it out, but only 4 packets of data can be sent...
Hi everyone,
for a project, we need to interface an analog sensor which is not using standard protocols like I2C or SPI.
Instead, it uses 6 pins to receive commands...
