Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
SDK:
nRF5_SDK_15.2.0_9412b96
Softdevice:
132_nrf52_6.1.0_softdevice.hex
Hi Sir,
I want add NUS function to ble_app_hrs_rscs_relay sample code and I add...
Hi,
I use a central with 4 peripherals connected with BLE protocol.
On the central, I use the radio notification interrupt. I would like to know which peripheral correspond...
Hi,
I have a problem in my application, i want to add scanning feature, but
When i call sd_ble_gap_scan_start () with these parameters it returns error (0x06) (with...
I am a begineer in Nordic trying to read voltage and current readings from ADC pin. I need to read both values in parallel, with known interval. So I need to use interrupts...
I am trying to use the LTE Sensor Gateway app to send Running Speed and Cadence Service Sample Application data loaded on a nRF52832. I have managed to get this two device...
Hi,
I have a problem with timer and nrfx. I use the migration guide:
So I r emove the old configuration entries related to the nrf_drv_* drivers from my sdk_config.h...
Hello,
I am currently using nRF52832 with SDK v11.0.0 and S132 v2.0.0. I am also using the soft device as my application requires. I have been trying to put the CPU into...
Hello, When i try to use nrf9160 with the BME280 sensor over I2C i get this error
***** USAGE FAULT ***** Illegal use of the EPSR ***** Hardware exception ***** Current...
Hello,
I am using BLE+MCU MBN52832 module and i am facing one issue while programming my application.
I am uploading the hex file using nrfGo Studio and when i try...
I have a custom nRF52840 board that I am implementing the Open Bootloader (from SDK 15.3). Push Button/Power control is handled by the STM6601 device. It keeps the power ON...
When I open a new project in SES and paste the code of blinky led example from " \nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky\pca10040\s132\ses ", and start compiling...
Hi. every one
First of all, i am a beginner.
I connected the max44009 and CJMCU2080 sensors to the board.
and also get a value.
but sgp30 sensor is faile
there...
HI. i use SEGGER Studio and SDK 15.3.0.
I usally use printf func for debug. however as use SDK func, I need to use NRF_LOG_INFO casue SDK file use NRF_LOG_INFO for debuing...
Hi,
I am trying to port an existing project to a Mesh SDK example. Some files include the math.h library and use the round function. During the build process I am getting...
Hi I use nrf-ble-driver ver.4.1.1 with PCA10031 dongle (nRF51844 chip on board) and "connectivity_4.1.1_1m_with_s130_2.0.1.hex" firmware for that dongle. in this case ATT_MTU...
