hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi. We are using the nRF52 sdk v12.1 with S132 v3.0.0 on a nRF52832. Once in a while (could be after running a few hours, could be after running a week) the application ends...
Where can I find the right documentation to start understanding the Nordic Thingy FW? Do we have any design document for this?
I need to develop my own application on the...
Hello,
I'm looking for some general guidance on the following application:
1 nRF52840 based gateway to cloud, on power supply
a few hundred nRF52832 sensor nodes,...
We want to use app_timer_create/app_timer_start to create a periodic timer, but noticed that there were a few seconds missing. After printing out each tick, we see that there...
I can't open my tickets since it's changed into private ticket by your engineer.How can I do?
My ticket' name is"about service change can't receive BLE_GATTS_EVT_WRITE"...
Hi,
I will work with nRF51822. I installed all software tools and I connect target device with debugger.
Should I connect nRF51822 with power like battery (because I will...
I used SES and wrote a printf message at main entrance: when I run in nRF Connect I can see the message that I wrote just after I press the RESET button (OK). Still, as I...
Hi,
What is the GPIO pin state during reset, and during startup ? I have seen that it is a high impedance floating input. How much is the value of this impedance? Can I...
Hello,
We're beginning FCC certification next week and I've been creating radio test and DTM versions of firmware that can run on our hardware for the lab. Everything looks...
I am using the nRF51422 for BLE data. My antenna matching network is this:
However, compared to the DK I am getting lower gain (DK gives -50, my PCB gives -64). I have...
Hi,
I want to load both "SPM" and "http_update_ota" code separately to the nRF9160.
For that as suggested in " http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.4...
I've been trying to configure a second UART for use on the nRF9160 DK. However, I'm having some issues getting anything to send over the UART. I feel like I'm missing something...
Hi,
I use the nrfx_rtc_tick_enable() function to enable tick interrupts for the RTC.
I have a statemachine that in some states disable the interrupt and sometime enables...
