When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I develop an program with BLE DFU support, but we hope to merge all hex as single hex file. Then we can burn this hex file by programer (such as jlink or NRF52DK), So we have...
Hello,
I'm trying to run the s132 (and s140) softdevice while running a proprietary mesh network stack. Naturally I'm requesting a hefty amount of radio slots. I need to...
Dear Nordic,
I have an application which contain UART and BLE advertising. For power consumption i use enable disable UART.
Enable and Disable Uart:-
Is it right way...
hi..
i am using nrf52832 and a peripheral device .. temperature sensor ,my temperature values are increasing like(0 ,27,75,80...) how to get a approximate value .
i have...
Platform: nRF52832 using SDK12.2 and Keil 5.20a
I've encountered strange corner case when displaying negative floats using NRF_LOG_DEBUG .
My test code looks like this...
I want to use BLE 4.2 Data length extension to stuff more data into one packet. I am looking at the "ble_app_att_mtu_throughput" example and am getting confused because there...
Hi!!
I am sending data by BLE data received by SPI.
The interval for sending data at BLE is 64 ms.
I have written and run NRF_SPI 1 -> ENABLE = 0; and NRF_SPI 1 -> ENABLE...
can't open 'J:/Projects/..../Electronics/SDK/BT840F/nRF5SDK15209412b96/nRF5_SDK_15.2.0_9412b96/examples/ble_central_and_peripheral/experimental/ble_app_att_mtu_throughput...
If there are multiple beacons, let's say B1,B2,B3,B4,B5 and a BLE receiver. I want receiver to only wake up from sleep mode when B1 transmits(long broadcast interval) and...
Hello Nordic community,
is it possible to configure the network key, application key, node address with the help of a byte array? The keys, adresses and all the peripheral...
I can not transplant SDK15.2's ble_nus into my project, there is no errors after i complie it, but when it does not work, I use RTT to see the errors, like this:
line...
Hi, I have trouble when working with my application bases on UART project on nRF51822 board. I use NRF Connect applicaton on my phone to connect with my board. Sometimes i...