Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
My setup is as such.
I use SPIM1 and SPIM2 all the time. SPIM1 goes to a set of MEMs devices, and SPIM2 is dedicated to a Memory module.
My device runs in of...
20170119_104909.jpg
I'm working with a ble open source.
Here i attached the captured abnormal case of the connection update
Request PDU from the slave. Please refer to...
Hi
I ordered Nrf52832 DK board instead of ordering nrf52840 Preview DK. I need to test bluetooth 5 stack,range ,bandwidth and through output.
Is the nrf52832 will support...
Recently I am working on a project transmitting and receiving data directly using RADIO block. The examples provided in the SDK folder use block wait which isn't the best...
I'm having alot of issues testing the PCA10031 running the MasterEmulator ProxmityDemo Example. It will open the port fine to the dongle, but always fails to Start Discovery...
Hi everybody
I try to reinitialize the Advertising with new parameters after a finished advertising. For example use directed mode, change advertising data and so on. But...
Hello everybody,
I'm designing an app to track the position of the smartphone using six beacons; I would like to know if there is an optimal orientation of the antenna...
Hello all,
After several tests about extending Timeslot, I have some questions.
I found out that the Timeslot will keep extending automatically after a successful...
Just a beginners question. I've read about central, peripheral, client, server, but i am still not sure how to choose. I use nrf51822
I want to create a beacon that has...
Hello,
I am currently working on an ultra-low power project that requires reading an I2C accelerometer multiple times per second. After analyzing the current consumption...
Hello,
we've got a problem with iOS 10 connecting to a peripheral using nrf51822 with S110. When bonding an iOS device to the peripheral the first time it works o.k. If...
Hi,
I am using BMD300 to develop my projects. I am working on SAADC sample example in SDK12.0.0. I am sampling the SAADC at a rate og 1000 sps. following is the saadc_ini...
Hi,
I want to set the reset bit to 1 in the reset register of Power Management module.
Chip used in nrf51822.
I have been trying to set the bit using the following statement...
how to send hex by nrftoolbox APP uart?
I use this app, when I start use it, I just only can send char, I can't send hex to the device. how to set it char to hex? please...
