Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello everyone, I want to measure Low power mode current consumption in nRF52 DK,but I dont have accurate CRO to measure in micro Amperes, therefore I would like to know if...
the eclipse build memory map is
text data bss dec hex filename
363312 2485 5340 371137 5a9c1 ********.elf
363312 2485 5340 371137 5a9c1 (TOTALS)
it is giving very large...
Hi Friends, I like Nordic and Arduino, it's great if Nordic can support Arduino officially, we can use the ARM0 in Nrf51822 as a single control point of Arduino project. There...
I taken the Android-nRF-Beacon-for-Eddystone app code from github.
From my account I configured my Google Dev console:
enabled proximity API
added credentials...
Hi all,
I followed the tutorial listed below:
devzone.nordicsemi.com/.../
I want to use SEGGER_RTT_printf but I always get this error:
Error: L6218E: Undefined symbol...
Hi,
I am working on one project in which I want to connect my two custom borads with S130 softdevice but I am not able to do that. My custom board has nRF51822 chipset...
I would like to implement a simple code to use SAADC on NRF52 to sample one channel at maximum sample rate (theoretical 200KHz).
All the examples I have found use limiting...
Hello All,
At a time either ble nus or dfu can work.
I have an problem with the services ble nus for uart and dfu does not work simultaneously means if i am adding both...
Hey, I got 2 beacons which I have connected via BLE successfully however I have some problems with BLE_GATTC_EVT_HVX event. Every time I get only one BLE_GATTC_EVT_HVX event...
Hello,
I measured the current consumption at 0 dbm of the app beacon example.
During the TX send phase I measure a current of more than 11 mA. Thats too high when I compare...
Hi,
Since I want to start to develop an Eddystone beacon and found the Github nrf5-sdk-for-eddystone . I am wondering if the Eddystone beacon is detectable by an iPhone...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update.
if 1 step is done, application update...
