hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi all,
I have the nRF52 DK programming consistently without any trouble both on Kiel and using the nRFgo Studio.
My problems arise when I connect a 3rd party module...
Hi,
im trying to set up 3 PWMs for simulating a RGB LED with the 3 leds on the nrf52-dk.
I need the following behavior:
pushing on a button increases the width of the...
Hi,
I have implemented a custom application(Lets name that file app.hex) which works and sends the data to phone via BLE on my nrf51822 DK. I am using the s110 v8 softdevice...
Due to some constraints in the manufacturing process of my product, there is substantial mechanical variation in the BLE antenna. I can constrain this variation to a degree...
Hi,
I am trying to program MDBT40 with Jlink and having some problems.
Here is the scenario:
I have two versions of the MDBT40. One that I took off a BLE NANO (RedBear...
Hi,
I tried to get the sample ble_app_uart to work on NRF51422_DK with the S130.2.0.0 soft_device.
The compilation and programmation of the board is OK.
The soft run...
Hi all, i recently posted some topics about my application to receive support, everything went good but now i need to add a last step to the project, and i would like to have...
I am using nordic_sdk_10 for PCA10001. what are the BSP changes and config changes needed after replicating PCA10028 for DFU over UART.
I just changed CFLAFS & ASM FLAGS...
Hi,
I am storing data using pstorage module but when i power off my nrf51-dk board, the contents get deleted and not retained in memory. What could be the reason for that...
Hi,
For a new design with nRF51822-QFA, planning to use Johanson Balun and Chip antenna as shown in attached diagram. Not using any tuning components between Balun and...
Hi,
I was wondering why DFU_IMAGE_MAX_SIZE_BANKED is calculated as
(((DFU_REGION_TOTAL_SIZE/2) - DFU_APP_DATA_RESERVED))
and not
((DFU_REGION_TOTAL_SIZE - DFU_APP_DATA_RESERVED...
Hi, I'm using ble_app_uart application from latest nRF52 SDK on IAR compiler 7.1 and PCA10040 board.
It loads and runs debug code, but it does not add breakpoints on any...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
