As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
I am using a Mikroe development board with the nRF9160 to establish an LTE connection and send MQTT messages to a broker. The application successfully connects to the network...
I have used the nRF52832 on a few dozen projects, usually at 3.3V etc. On this project I have it at 1.8V, which may be related, but spec is 1.7V min, and the 1.8V supply is...
Hi Noridic team,
I am developing with nRF5340, and I added the following configuration to the prj file:
CONFIG_SPI_NOR_INIT_PRIORITY=75
However, I got the following...
Hi, I cannot compile because of the error below. Thank you in advance for any help.
I have updated the toolchain and sdk recently. Tried also with 2.6.1 and 2.7.0, the same...
I am porting the LoRa Basic Modem to the nRF52832 , using the nRF5 SDK and Segger Embedded Studio (SES) . In my application, I am using SoftDevice and implementing FOTA ....
Hi,
We recently updated our NRF Connect SDK from v2.2.0 to v2.7.0.
After porting to the SDK v2.7.0 we are not able to build the project with DFU enabled. We get below...
What is the best method to ensure the nRF9160 LTE functions on a PCB during assembly with minimal test equipment? Our thoughts were to search for available networks using...
We want use NRF5340 to do le audio application. We got the demo from your website, and find the audio demo, but the min sample rate is 32khz can be set, we want to use 8K...
I'm working with a client's existing product. It has an external MCU connected to nRF52832 via SPI.
The nRF application & SDK code are compiled inside the external MCU source...
I now want to use the 52833's board to burn the host program and then connect to other nordic slave devices. But now I put \nRF5_SDK_17.1.0\examples\ble_central\ble_app_uart_c...
Hi All,
1. The SDK used in VS code is version 2.6.1, and running the periphral_uart demo can print in rtt, but not in sid_end_ device
The official routine is used for...
Hi
First of all i am quite new to nRF SDK so if the answer to my question turns out to be trivial then I am sorry.
I am in the process of developing a Zigbee light switch...
I need to check if the Ethernet cable is connected or not, I am using the eth_click for ENC28J60. I see the driver does not allow me to see directly if the cable is connected...
Hello, How can I purchase a nRF9131 EK from Nordic Semi Sales? I was informed at the recent "Getting started with NR+ PHY" webinar that nRF9131 EK can only be purchased directly...
I would like to take Nordic's "TF-M secure peripheral partition" sample project, and modify it to take data received from the secure peripheral and send it wirelessly to another...
