Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
We are referring to demo project ( https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo ). This is quite matching for our requirement. However we have...
What is the default state of the GPIOs after reset, until my code has a chance to configure them?
Are they all Input/HI-Z? Is there a place in the manual that specifies...
Mesh DFU works like:
if(fw_updated_event_is_for_me()) update_ and _relay(); else relay();
Is there a way to change this behaviour to:
if(fw_updated_event_is_for_me(...
Hi,
I'm working on porting a project from an NRF52840 to an NRF52832. Apparently I screwed up something somewhere and I can't compile the project anymore. I'm using GCC...
Hi,
I working on a project that need to communicate with other mcu by SPI, the communication is work, but I have question about the start and stop of communication.
...
Hi,
I just met some difficulties to implant more then one service into my project. The project was developed based on hid_keyboard.
The project can work normally when...
I am using 2 nrf52832 boards to talk to each other through UART. One is programmed to the central SDK example and other other is peripheral. In the code, i incorporated 2...
Hi, I got the issuse about the connection with nRF52810. I used nRF connect to connect the nRF52810 device via Android,but it isn't easy to connect successfully.The nRF log...
Hello,
I have a question about the nRF52840 device and the supporting documentation. I am trying to figure out the current ratings for the GPIO. On page 198 it states that...
Hello,
I have an issue with the function sd_flash_write which ends up in a hardfault when returning to the function calling it. I know there are many Q/A on hardfaults...
Hi,
I have some questions about UART:
Currently I am developing software on our PCB with nRF51822 chip. When I was implementing and testing software on the Development...
Hi,
I am a beginner to BLE. I am using the nRF52 DK and i want to try out the advertisement and connection features.
I basically want to know how to send out an advertisement...
HI
when I use nrfutil.exe to generate .zip file on win10 64bit, I got the UnicodeDecodeError.
And :
Python version 2.7.9 (default, Dec 10 2014, 12:28:03) [MSC v.1500...
In my current project, I am receiving multiple indications from peripheral device. After 25 indications, I need to pause the indications or disable the indications. I am using...
