hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
So I have implemented the UART BLE mesh code as mentioned in devzone.nordicsemi.com/.../send-and-receive-a-string-via-access-layer .
Now I am able to take inputs from the...
Hi,
1.
I feel really stupid as I cannot make any sense of any of the information found in Product Specification (v3.3), or the online Compatibility Table or past forum...
We can know the state of radio by checking NRF_RADIO->state register value, but is there any way that we can be "informed of" the state transitions of this register instead...
I want to demo the NFC provisioning example on Github. Unfortunately this app is not complete.
https://github.com/googlesamples/android-NfcProvisioning
Is a complete...
Hi. I'm using nRF52832 SDK 13.0.0.
My device is peripheral and it is advertising every time.
Now I want to change advertising packet and scan response packet every time...
Hello:
We have a BLE project running on the BMD-300 from Rigado for which we want to add BLE DFU functionality. I am basing our development on the "ble_app_buttonless_dfu...
Hello,
I want to measure the current in system off mode.
I am flashing the S110 softdevice and bootloader in the nrf51822 chip.
Using BLE i am flashing an application...
Hi nordic
I'm developing using nrf52832
This board has many example code so I'm developing smoothly
but Today I had problem. It is about check time
I want to check...
Hello, I use light switch example (nrf52832, mesh sdk 2.0.1)
Can I create mesh network without servers? (clients will send messages to each other and process them)
And...
Hi, I want to use 2 I2C instances and 2 SPI instance during setup, and later switch to 1 I2C instance and 3 SPI instance. To do this, I tried to swap TWIM2 instance to SPIM2...
I'm looking to build a product which require an Android board with relay and BLE 5. I am very new to this and so far I have been playing with Raspberry Pi where the BLE and...
Hello, this will be a bit of a long-winded explanation but here goes: I'm building an SPI driver that reads data from an external ADC and writes to a PWM signal. I got the...
I figured that I could put
#define TX_POWER_PHIL +8 /** -40,-20,-16,-12,-8,-4,0,+2,+3,+4,+5,+6,+7,+8 phil **/
and then make two changes to
static void advertising_init...
Is any GPIO, as output, logic level on nRF52832 maintained when the device is in OFF mode? Same question when the system is in ON/Low power mode Thank you
