I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
hi,
1.I find some same issues on website, most of them can send more than 1 packet per connection interval up to 6 packets, but I'm not sure what version of sofedevice...
Hi!
We are using S130 softdevice in peripheral role and achieve the specified maximum throughput of 63.4kbps ( S130 spec ) when communicating with a PC and connection interval...
Dear sir,
Reader has a NRF24L01P-R7 with stm32f4xx controller.We are using TAG chip NRF24LU1P-F32Q32-T.
Please share the independent stack information(source code) so...
I am trying to setup the examples for the dev board PCA10040. I copy them from the Pack Installer and when I open the project I keep getting "Install missing Software Packs...
Hello
I made a custom service with characteristic. It send the number 1234 over ble. When i open the Master Control Panel and look at the custom characteristic. I read...
We have a home made BLE device based on nrfR1822. This one has two embedded sensors sampling data at a frequency of 25Hz.
In regular mode, the device sends every second...
I was going through Gazell link layer as well as Enhanced shortburst i found in both of them we can use payload max upto 32 bytes. Both supports 8 nodes with an host using...
I just received the nRF52 demo board PCA10036 V 1.0.0, and I also downloaded the latest SDK nRF52_SDK_0.9.2_dbc28c9
I programmed the softdevice hex and then programmed...
Hi BLE Developers,
I'm developing a BLE peripheral device using S110 softdevice which doesn't have any input or output capabilities and will communicate with smartphone...
Hi,
I am using the iOS nRF Toolbox and integrate it to my Swift project.
After that, I got this error message.
Undefined symbols for architecture x86_64:
"_crc32"...
my dk board : nrf51422 and nrf 52382,
the central role : nrf51422, and the peripheral role is 52382.
my sdk version : 52422 is 10.0.0 and 0.9.2 for 52382
the project...
I've been trying to wrap my head around the app_twi library by looking at the examples, and I'm slowly getting there.
However, for my application I need to send multiple...
There is a fair amount of documentation suggesting that a Raspberry Pi or consumer router running OpenWrt can be set up as an edge router for Bluetooth.
The builds involve...
