Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
From the datasheet, the On mode with all blocks idle draws 2.6 uA.
In my code for the PCA10001, I immediately set:
void sleep(void)
{
__SEV();
__WFE();
__WFE();...
I was going through online material all of which mention that the profiles and protocols (GAP,GATT,L2CAP) i.e. the host for a BLE implementation is a software stack rather...
Hello - I have gotten blinky_example up and running in eclipse using the SDK 5.2, nan-29, and some additional google-fu.
Now when I press debug and the play button, it...
I am trying to use nRF UART app and nRF8001 chip. But I cannot change the device name. I intend to change the device name after nRF UART app detects the device. Plus when...
I'm trying to create a method so a users can initiate an OTA update from a paired device. To that end I've written something which is supposed to invalidate the data at the...
I'd tried some first steps using nRF Sniffer on a linux host.
Within sniffer_uart_protocol.xlsx I read something about the Uart packet format et cetera.
I'd programmed...
I am trying to get ble_app_beacon exampel working on the PCA10001 on my nrf51822 working. However when I simply run and reach APP_ERROR_CHECK(err_code) inside "advertising_init...
Reading through the nRF51822 Beacon reference design it states that there are Keil ARM project files available. Does this mean that the example code given after purchasing...
Hi all。
I am programming a nRF51822 chip, using the S110-nRF51822_6.0.0 soft device,download ble_app_hrs.hex。
I used app name "nRF Utility".I can connection nRF51822...
Hi,
i have some more, for me fundamental, questions and i hope some one can help me :)
1.) can i use the advertise function whenever i want or only in connection interval...
Hi All,
can any one please share information related to this
1)please explain clearly about channels and pin?
2)can 2 gpio pins hooked to a single gpio channel?...
I'm not sure if this belongs properly here - but I wanted to send out a thank you to Ole Morten.
I saw your reply in http://www.funwithelectronics.com/?id=168 and this...
Are there any plans to create a Google Glass compatible app like the nrf UART app? I'm trying to link a microcontroller with Google Glass via your bluetooth low energy module...
I'm using the Arduino SDK but I don't think that should matter for this comment. I think a small change to some of the lib_aci functions would make it easier to use them....
Hi,
I'm using an arduino uno with a readbearlab shield with v1.1 to send sensor data to a android phone.
Using a timer interrupt I try to send data every 0.1 sec (10hz...
