Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi,
We have a nRF5340-DK board with the following setup:
b0 as the first stage immutable bootloader
MCUBoot as the second stage upgradable bootloader, which needs...
Hello, I have an issue with a project I'm working on with a nRF5340 Audio dev kit. I am using VSCode with the nRF Connect SDK plugin, and SDK version 2.6.1.
I need to have...
Hi,
We are working on nRF5340 with TF-M enabled and iOS application.
What we are observing is the peripheral device MTU TX and RX are configured to 512 bytes whereas the...
Hi I'm using nRF7002-DK kit and I noticed that the output voltage of a GPIO is 1.8 V instead of a 3.3 V. I have encountered a solution mentioned that we should apply these...
I’m working on an nRF52832-based project using the Nordic SDK (v3.5.99-ncs1-1) and MCUboot for OTA updates. I have a 512KB internal flash and 4MB external SPI flash (P25Q32H...
we are using SPI3 in nrf52840 with nrf SDK 16.0
we are using this as below
1. SPI3 init -polling mode
2. SPI3 unint
3. SPI3 init - DMA mode
4. SPI3 unint
5. SPI3...
Greetings,
Is the command toggle_dcdc_state supported in the radio_test sample when compiled for the nRF5340? ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples...
I started with the BLE provisioning sample (ncs\v2.7.0\nrf\samples\wifi\provisioning\ble) using nrf7002dk/nrf5340/cpuapp build target with sysbuild which works fine to provision...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
I am trying to use the `ram_report` tool and the results seem to have some issues:
1. The total size reported is much more that that reported when linking the zephyr.elf...
We are not using system off mode. since we not using external rtc. We are using internal Real Time counter in system on idle sleep (using ksleep).
In Basic led code , We...
We are building a Bluetooth remote using nRF52810 and nRF connect SDK v2.5.1
The remote have 20 buttons to be transmitted every 100mS, and we need several LED on / off commands...
I am trying to measure the battery voltage on my custom board which is based on the nRF52832 device. I am using nRF Connect SDK 2.7.0 in VS Code. The dts file for this custom...
Hi，
We had some trouble doing the certification of Tepec， Telec certification requires the RF power accuracy of ±3.8dB , while it is ±4dB in spec。Do you have any good advice
