hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
HI,
I am playing around with the "usbd_ble_uart_freertos" example of SDK version 15.3.
When I create another Task and try to write log entries (NRF_LOG_INFO("Test")) i...
Hi,
As well know, there have 100 channels in ESB function in nRF52832, but 2.4GHz also share with Wifi and Bluetooth.
So there have many noise if I choice wrong channel...
Hi!
I am experimenting with the ble_app_hrs_freertos example.
I would like to start two additional tasks. All works until a ble conection is made. after that my created...
Hello
I am using FDS to store some MAc addresses in my project. After successful I try fds_init() which returns error 11.
I can't figure out what is causing this error...
Hello, I have been trying to get the nrf9160DK PCA10090 version 0.8.2 to connect to your nrf cloud. I initially tried with the provided ibasis sim. I was able to get it registered...
Hi,Master:
1.The timing of the underlying nrfx_qspi_write(...) function is:a. Send 05 to check if the wip bit is 0. (Here, if wip is not 0, will it always detect until wip...
Hello,
I am going to be heading to a certification house to run tests to pass for the CE mark for our product that we used the nrf51822 on. The BLE portion of our product...
Hi everyone,
I'm trying to establish throughput test using mtu_throughput example(central-peripheral) and 2 nrf52840's but I keep getting error when set phy to coded. Here...
Hello All,
I want to know if I can run all this protocol at once? if yes can I find an example or can you suggest me a guide? I know there are examples to use BLE and ANT...
Hello, I'm attempting to establish a data connection on the VZW network after uploading a VZW IMEI to the ODI portal. It appears there is no module available under the Nordic...
We are incorporating a filesystem for NAND flash driven by the NRF52, but we are running into performance issues using littlefs and want to do deeper troubleshooting. From...
Hi Everyone!
I really need some help. So I'm new to Nordic semiconductors and Segger Embedded Studio IDE. I purchased myself an nRF52832 breakout from sparksfun and nRF52832...
Hi,
I am trying to test the Amazon FreeRTOS BLE demo ( https://docs.aws.amazon.com/freertos/latest/userguide/getting_started_nordic.html ).
I followed the instructions...
When I connected the development board with komoot (based on Android), komoot repeatedly disconnected again. The chip platform is nRF52832, and the protocol stack version...
Hi,
I try to rotate an image (180) with nrf_gfx_rotation_set(p_lcd, NRF_LCD_ROTATE_180). This only works once, but after, I want to return to the original position by re...
