dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
We are sending data every connection interval which is a stream using the API sd_ble_gattc_write. Whenever there is a dropped packet from what we understand, the Softdevice...
I used SDK11, SD332, and no change anything.
the application reset as picture.
can you test this issue and give suggest ,why app reset?
D:\work\nordic\BLE\SDK\nRF5_SDK_11...
I need a code example (e.g. Health Thermometer) that runs on the Beacon Kit. I have tried several combinations of soft devices and code examples, but I can't get it running...
Hello,
I started implementing a project with the device manager. I am using the S120 as central.
I am able to connect to 3 peripherals at the same time (also nordic nrf51822...
Hi,
The environment is Ubuntu 16.04 running on parallels on a mac pro.
I am following all the installation instructions and I get no errors, except that the opus driver...
Hi,
Today, i try to use the UART SERVICE from nordic on both smartphone and NRF51.
I succeed to send data between the two.
But now, i want to send data longer than 20...
Hi,
Using SDK12.1 with nrf52. Have SD and bootloader on the device and trying to load application via BLE DFU.
It randomly gets stuck. (see attached screenshot)
And...
Hello,
I have some trouble to use the Secure Bootloader example, which comes with the
nRF5_SDK_12.1.0
I installed the latest nrfutil and hexmerge. I can compile the...
This piece of code appears in all IoT SDK examples:
eui48_t ipv6_medium_eui48;
err_code = ipv6_medium_eui48_get(m_ipv6_medium.ipv6_medium_instance_id,
&ipv6_medium_eui48...
Hi, I am using the nrf uart app to communicate with a smart phone and the NRF52. I am trying to detect whenever it is sent a value between 0 and 60 from the phone, and save...
Hi,
I'm working on nRF51822 with SDK 11.0.0 softdevice s130
I have an nRF module acting as central and smartphones (iOS and Android) acting as peripheral.
I tested...
Hello, what is the BLE max range w/out usin PCB antenna?
And what range ll be if i reducing the connection interval down to the minimum 7.5ms, set Tx power to +4dBm using...
I am using the nrf51822-QFAC-R in an application where the realization of the antenna is very challenging, and I expect to have an antenna |S11|=-1dB, with variations of the...
Hello, I want to clear things up a bit, all these concepts are starting to overwhelm me somehow. I want to know:
What can have UUID and handle? I understand that profiles...
I want to use ATMEGA 328 to send a packet over to the chip as follows:
SPDR = packet ;
Can some one kindly post what the content of this packat should be ?
is it possible...
