I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
How to make an encryption on nRF51822?
Does it need to set
sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_SUCCESS, &m_sec_params, &sec_keyset)
the...
I want to flash a client and three servers with the BLE mesh simple light switch example:
infocenter.nordicsemi.com/index.jsp
The third instruction on the above web...
Hello,
I've recently properly started programming my nrf52832 DK with segger embeded studio playing a little with the debuging tool break points modifing example ect.....
I test ble bond with 'ble_app_gls' in sdk 12.3.0
eg.nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_gls\pca10028\s130\arm5_no_packs
my phone is meizu mx4, android...
I feel Slave Latency is unnecessary.
For example :
Connect Interval is 100ms,
Supervisor Timeout is 4000ms.
So the Slave Latency must be 39.
if I set Slave Latency...
Hello,
When using extended ATT_MTU without DLE, and the MTU is larger than the LL data length, I know that the MTU is divided into smaller LL packets when sending.
But...
Dear Nordic Devzone,
I want to run an Arduino Ethernet Shield with the Wiznet5100 on the nRF52840. I was wondering if there was an easier way to do this then having to...
I am designing the BLE solution using nrf52832 . The board will be two layer board with solid ground plane in the bottom layer and signal and ground pour in the top layer...
what is a valid publish handle, when I run pb_remote_client, first I input "1" and one pb_remote_server device has been provisioned, and then I input "233", it happens "MESH...
Hello,
I used translation software.
I am measuring current consumption.
I supply it from an external power source.
I connected the SB 12.
After that, I supplied...
Hello,
I'm having trouble to work on the nrf52832 DK with the accelerometer.
First, I tried to wire the accelerometer as I was wiring it on a Arduino Uno but I couldn...
Hi everyone, maybe I'm wrong but I think that the Garmin oregon 600 uses a ANT+/BLE chip made by NordiSemi, it's possible to know exactly which one it is?
Thank you a lot...
Hello,
i'm trying to DFU from 13.1 to 14.1..
What i have tested is flash(SD + B) + dfu(APP) on both versions. Now i'm trying to DFU all from sdk13.1 to 14.1.
Is it...
I know that latest nRF5 SDK and nRF mesh SDK support SES, it's really a good news for developer. I'm just curious that, can I use SES to flash SoftDevice on macOS? If so,...
