As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi:
I set up a peripheral on nrf52832 and add beacon_info data as Manufacturer specific information。The version of softdevice is s132.
memset(&scanrsp, 0, sizeof(scanrsp...
Hi,
My sensor uses SPI communication and need 32.768kHz external clock pin FCLK , I connect 32.768kHz clock to XL1 and XL2 but my problem is which pin can I use it for...
Hi All,
I've integrated the flash routines from this example:
github.com/.../nRF52-fds-example
into my project, and am having problems figuring out the architecture...
Hello,
I've done this with an Arduino and 1Sheeld Bluetooth LE shield, but want to try with the nRF52 dev kit. Just looking for any starter code/examples/tutorials to help...
I have a piconet of 4 devices, where 1 device is a master and 3 devices are slave.
Communication continuously occurs between master and the slaves.
But then the master...
After looking at Nordic's Bluetooth 5 implementation for nRF52840 and other chips -- it appears that Bluetooth BR classic is not available. All I see is BLE and BLE functions...
We are working on a project using nrf52832 module and GPRS device. Here we are facing a challenge in updating the firmware to BL652 over GPRS and server.
nrf52832 is connected...
Hello, a quick rundown on the problem here:
New versions of Softdevices S140 corrected an error and now correctly ignores writing to cccd descriptor using write instead...
I have 4 devices communicating in a Bluetooth piconet, where 1 device is the master device and 3 devices are slave devices.
I want to time synchronize the 4 devices to...
Hi,
I'm using the S132 v3 and wonder about the impact of DLE on scheduling.
In the chapter on Scheduling in the softdevive specification is writen that multiple peripherals...
I would like to setup the just released RasPI demo using the Nordic-Thingy52-Nodejs repo
I don't have a dongle, but 4 PDK 52840 boards and 2 Thingys.
Can I still use 1...
I found that blindly configuring all GPIO pins can stop the LFXO and RTC counter. I am reporting this as: something to be aware of, not obvious to everyone. Not a question...
I am testing the nRF52832 in Rigado BMD-301 module. I am able to get to ~40uA when advertising ,UART enabled but not used and all other peripherals disabled. But as soon as...
I connect to my BLE peripheral device using NRF connect app. While in connection, if I switch my phone's bluetooth off and turn it back again and then try to connect to my...
