Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
Hi.
what i want is using 52840 dongle, test ble communication with custom board.
custom board use 52832 and it flashed BL + SD + APP.
I checked it is work using pc connect...
Hi,
we have a custom PCB board equip with nordic 52810 chip and the system ARCH is acting like Linux Host-BLE_Controller mode demonstrate below
Our manufacturer needs...
I need to send and receive data from the UART of many nodes to the UART of one specific node.
I use is the nrf52840 PDK with segger-studio. Is there a sample available to...
I'm trying to enable UART in a mesh application with SDK 15.1.0 and mesh SDK 3.3.0. This seems to be a real nightmare and I'm not sure why Nordic has so many different HAL...
Hi everyone. I'm trying to add UART Service to Mesh light switch example in Mesh SDK latest version 1.0.1. Is it possible? And When Nordic will provide integrated Mesh SDK...
Hello everyone,
I am currently working on a project, where I want to interface UART to a Bluetooth mesh network. The project is very similar to the light switch demo, because...
Hi Team,
I am working on Mesh SDK 3.10, I have requirement of mesh with Ble Uart. So I decide to take this example "ble_app_uart_coesixt". I build this example without...
Good day, support!
I have a couple of questions regarding the firmware of the nRF52840 dongle.
1) How to identify the firmware version that is nRF Connect flashing ...
After following the " Using a custom Secure Partition Manager with your application " Guide for the nRF5340-PDK, I experienced following error:
I tried to create a Non-Secure...
Hello every one.
I am new with Segger and nRF52.
I tried to create my own library for OB1203 sensor.
But i stack here when Segger view this error: Below is my screen...
As we are performing climate tests for custom PCB based on Nordic nrf52832 SOC, in low temperature i.e -20 Deg C the communication is not stable. After verifying the HFCLKSTAT...
Hi,
We thought to have a setup like this
1<-->2<-->3
1 is MESH ADV device with some mesh model
2 is MESH ADV + regular BLE stack support
3 is Gateway with...
I am trying to collect sensor data and store in flash using qspi interface. Unlike the peripheral example code, the qspi data handler function is not getting hit with ble...
Hello, I have another problem... i work on nrf9160 dk
I try to send http post when i pressed button 2 but this doesn't work.. Below you could see my code who block on printk...
