HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Dear,
I am trying to test nRF52840 Preview DK.
Is there any method to test bluetooth 5.0 feature or spec?
Especially on speed and distance.
Thank you in advance!
Dear Madam/Sir,
I'm working with SDK14.2, softdevice5.0.0-2alpha, s140, and nRF52840 through the DevKit.
I'm recurring to the fstorage API to read/write/erase flash while...
Does enabling POFCON on nRF51822 lead to any increase in power consumption?
If yes then what is the value?
I struggle to find any information in Reference Manual or Product...
Hi
i am new with nr24L01 module , i am currently trying to configure them but , i am not able to read the RF_CH register just after write into it ? so i don't know if the...
Hello. I am using ble_app_uart from sdk14.2. I use pca100401, softdevice s132.
Advertising is generated using timer RTC. Board advertises and stops advertising without errors...
Here is our requirement.
We want to have four transmitters based on nRF2460 and more than 100 receivers. It means there will be four broadcasts.
Each receiver should...
Hi DevZone,
I am working on a project using nRF52840 preview DK and Arduino CAN Bus shield. I modified source code base on some Git Projects. It seems the SPI initialization...
Hi everyone!
I want to implement SPI with "ble_app_beacon" example with the following hw/sw.
DK : nrf52832
SDK : nRF5_SDK_14.2.0_17b948a
IDE : Segger Studio 3.34...
Recently,I use the SDK14 to develop the project,the initial project is in the content "SDK14/examples/peripheral/twi_scanner/pca10056",
Then and the spi example in the content...
I have build the light switch demo, it works properly. But I want to make multiple sensor node that takes data from sensor and send to single relay node. I am little confused...
I just integrated CMock which is part of my unit testing framework and i am trying to test a mocked function however i am running into RAM overflow error. Is there a way to...
May need to post this question to Segger, but I'd figure I'd ask here.
Have a nRF52832 project that compiles, links, and runs fine on the 52832/10040 dev kit board.
...
Hi All,
I am using the nrf52840 to run an application which does not use the BLE.
I need to add firmware update capability to the device so that I can push updated in...
Hi, I am running into a connection problem with connecting to the Secure bootloader example in SDK v13.1, whenever I try to connect I get Gatt 133 error. To my memory, the...
